How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello,
I am a newbie of Bluetooth development. I have a question that what is the difference between ACI (Application Controller Interface) given in nRF 8001 and HCI (Host...
Hello,
I have one Eval-Kit (v2.2.0) and I had no problems with SDK5.2.0 and demo programs defined in nRF51822 Evaluation Kit User Guide v1.2. Now I have installed SDK6...
Hi,
On a nRF51822 (QFAAG0) with S120 softdevice (using the recent PCA 10001 v2.2.0 board), i'm trying to perform these operations successively:
a simple RSSI scan...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
I want to use the AES of 51822 and I have read the nRF51_Reference_manual,I cann't find any demo about AES in SDK.Do you have the demo code about 51822 AES encryption...
Help please! I've been using the nrf51822-EK for several months. Everything has been working well.
I updated my SDK in order to be compatible with S110-SD-v6. Everything...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
am using nrf51822 chip communicating with PIC16fl1509 through uart.the PIC will send the temperatire values through uart to nrf51822. i have a doubt ! will the uart communication...
Hello,
The fact is that I was testing how to OTA update the kit's firmware. I had no problems with the app but when I tried to upload the bootloader.hex includen in the...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
friends :
i assume that the nordic support team can also be considered as friends.
i purchased a nrf51822-mkit, but it seems that it does not qualify for a legitimate...
Hi guys,
I would like to know how to use the softdevice to enable an interrupt when I receive an advertisement packet. Right now I know we have to use
softdevice_ble_evt_handler_set...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Good morning,
Is it planned to raise a new version of this application note but based on the new version of the SoftDevice? If yes, when is it expected?
Best regards...
