I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Is there a way to create custom battery profiles of non rechargeable batteries for the nPM 2100 PMIC? Is the nPM Fuel Gauge board compatible with the nPM 2100 EK?
Hello,
I am using nRF5340 with nrf v2.7.99-cs2.
We have interfaced External flash MX25R over nRF5340's QSPI channel. We are using XiP as well and some part of code lies...
I'm developing a Bluetooth mesh lighting controller on a custom board using nRF Connect SDK v2.6.1. I'm trying to add a Sensor Server model to report energy usage, but I'm...
Environment : nRF52833, NCS v3.1.1
Hi. I evaluate PAwR project in my Solution.
PAwR is Fine. But get/set Tx Power is issue.
before add PAwR, My solution used common...
Hello,
I am developing a custom IoT device based on the nRF9151 SiP with a Qorvo QM13345 SP4T antenna switch controlled via RFFE 2.1 interface. All RFFE AT commands fail...
Hi,
I am working on nrf52832 and using SDK 16.
I try to debug the ble_app_buttonless_dfu example, which give error on line 853 in main.c. err_code = ble_dfu_buttonless_async_svci_init...
We are in the process of developing a product using the Thingy91:X as reference.
We need to modify the hello-nrfcloud firmware to suit our application.
Could you suggest...
I am currently working with the Matter sample project and have encountered a question regarding the diagnostic log function. I would like to inquire about how to enable the...
I'm using nrf52840, v3.0.2, scanning BIG/BIS and printing out the BASE.
I first scan the extended broadcast with the label broadcast_id, and then establish synchronization...
I wish to install this program as stated in nRF Connect for Desktop. The install hangs at Downloading files... I am on Windows 11. I tried a few times with the same result...
I am puzzled by what I have observed using retained ram on NRF54L15. I have this overlay (see below). Essentially created 16 KB SRAM at address 0x2002C000. I have a struct...
We are trying to add ble mesh functionality to our current product, but encountering an error.
We are copying code from the ..\v3.0.1\zephyr\samples\bluetooth\mesh_demo...
To generate build configuration and build the app, you first need to: touch ncs/v3.1.x/bootloader/mcuboot/boot/zephyr/boards/nrf54l15dk_nrf54l15_cpuapp.conf
or copy it from...
I am currently working on the Matter certification for the light_bulb sample project , where I have integrated the Diagnostic Logs snippet during compilation. However, during...
