Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
The board connected to the PC for the first time, but after I mistakenly loaded the Bluetooth low energy sample instead, the Power profile on software nrf connected for desktop...
nrf51822's SWDIO/nReset pin is controled by a MCU GPIO output, a 1k resistor is in series. SWDCLK is connected to a pull-down resistor. And sometime (very rare) nrf51822 can...
Hi,
I am using nRF9160 multi cell location code on nRF9160-DK PCA10090 version 0.15.0.
Modem FW has been updated to the latest 1.3.1 binary.
I am using LTE-M with AT&T...
Hello there,
Recently I have added and been testing DFU into my existing application. I have conducted a few DFU updates and have noticed a semi-reoccurring issue. I use...
I currently have a working project with ethernet shield ( ENC28J60 ).
I use the driver from NCS 1.5.1.
I want to know how to enable logging?
I found some posts on this...
I am current evaluating the SPIS for the nRF52840 and experiencing incomplete transfers from a connected master (Arduino). I'm sending 'hello world' from the master to the...
I have checked out and built the iBeacon sample in zephyr (samples/bluetooth/ibeacon) for nrfconnect version 1.7.1. I tried building for both the nrf52840dongle and nrf52dk_nrf52832...
Hi,
I have a custom 9160/mfw1.3.1 board with a set of matching networks and I need to setup MAGPIO to control these. This will only be used for cellular, not for GPS.
...
Hello,
We have produced a product that uses the 82520 chip. This product uses the NUS service. We want the Windows PC to use its built-in Bluetooth to connect...
Hello,
I need a PMIC for a lithium polymer rechargeable battery solution.
The nPM1100 from Nordic is interesting, but I see there is a cap on the output current available...
I cannot get the blinky example to work with my NRF52 development kit. I used the example in the pca10040/blank/ses folder and it worked fine. I then modified the code per...
Hi,
I'm evaluating a NRF52833 DK running the peripheral-uart example.
My Galaxy 10E can pair with the DK and the nRF connect Android app on the phone can find it and connect...
Trying to diagnose an issue, and looking for documentation on the memory mappings for the nrf52833 using S140 v7.2.0 - something like infocenter.nordicsemi.com/index.jsp ...
