Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Dear supporters team,
I have a project need to build with a system that includes one central connection to multi peripheral.
do you have any project base similar to my...
Hey all! Today I tested the Asset Tracker App V2 (NCS v1.6.0) with the AWS implementation of the Cat Tracker App.
The rollout was totally fine at the end, and also the App...
Dear Nordic Team and Community!
I want to rise up the question again how to update an advertising message, especially the device name (on nRF52840Dongle, S140, 10059). I...
,i use a nrf52840dk_nrf52840 to run once a nrf5340dk_nrf5340 board's code , I change board name from nrf5340dk_nrf5340_cpuapp to nrf52840dk_nrf52840, change xxx .overlay from...
Hello,
I use central_uart (nrf52840dk) and peripheral_uart (nrf52833dk) examples, NRF Connect SDK v1.6.0
I want to send more than 20 bytes of data,
So, I increase UART_BUF_SIZE...
Hello,
I am using the nrf52840 controller for the development ,i want to read the value from 2 channel of ADC . I just gone through the SDK example code of
SAADC, here...
Hi All,
I was trying to transmit a bare-metal minimal C program to send a raw ADV_SCAN_IND PDU using nrf52840 dev board. Code is listed below:
Here is the linker script...
I'm currently building a device that has the following functionality:
1.) wake from sleep mode and wait 5 seconds for a potential button press
2.) if the button is pressed...
Hello,
I'm trying to debug an issue where a function I wrote that should only be called under a specific condition is calling in an infinite loop whenever the program runs...
Hi, I'm using nRF52805 S112 for my BLE project. I'm using an internal RC ocillator. I would like to ask something about the clock.
1) NRF_SDH_CLOCK_LF_RC_CTIV =16 and NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hello,
I am working on using the open_bootloader with our application and running into a problem.
We are using the GP_REG to jump from our application back to the bootloader...
Hello,
I'm using the following code to loop through the flash memory sequentially and send records created by the flash_fds example:
The data stored in the records...
Hi,
How does numeric comparison works? Shouldn't both devices share parameters in order to display the same number? How can we be protected from MITM?
Thanks!
