How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi I am using BLE Mesh V4.0 and Stack V 16.0.0
I have included UART functionality in light switch server code to interface a sensor.Now upon receiving 5 bytes from UART...
I'm new with Nordic products, I bougth one nRF52840 and I tried to install Segger, to start programming.
I had a problem when I tried to open a SDK on Segger. When I try...
I'm using a custom nrf51822 board with S110 softdevice, and SDK 10. This board is used as SPI slave with BLE. I tried to estimate the stat up power consumption by reading...
Hi, we are developing a bluetooth device in my company that must transmit at a distance of about one kilometer. I saw that this soc has been tested up to 1300 meters. It's...
1. By the toolchain manager, the sdk connect and zipped toolchain were downloaded.
I used the downloaded SES to compile examples. For others, they can compile successfully...
Hi All,
My one of the old application is based on SDK11 and i found some issue data corruption with FDS module. After reading some post here regarding FDS issues and also...
Hello,
I am trying to evaluate the Channel Selection Algorithms (CSA) 1 and 2. From what I found on here, CSA 2 is enabled by default in SoftDevice stack, could you please...
Hello everyone. I want to create project from stracth for nRF52832. I use nRF52 DK. I couldn't find any tutorial for this. I create new project under nRF5 SDK 16.0 and specified...
I am using BT840F module from Fanstel which is based on nRF52840.
Currently I am having two EV-BT840 (Evaluation kit for BT840). I have modified 'pca10056.h' as per my board...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello Devzone,
I've been working on a system to set notifications on time ready for transmission.
The client sends a WWR package to my peripheral and I want my peripheral...
Hello,
Currently, I'm trying to flash my custom board that has nRF52832 with an uart application that I integrated buttonless DFU. I'm running into a problem where when...
1.nrf9160 is there an RF calibration parameter at the factory?
2. If there are calibration parameters, does burning mfw_nrf9160_1.2.0.zip firmware affect the calibration...
I have two devices here, So I combined three HEX files and burned them with JLink, and they don't behave the same. One starts the application normally, and one is always in...
