I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
I'm working on a project involving pressure sensors.
These are to be read out via UART and then transmit the data via Mesh to a relay node up to a PC, which visualises...
Dear Sir or Madam, I am asking advice on the following matter: When trying to port the "pin_change_int" example to a nrf52833 DK the code compiles but is not showing the expected...
Hello, I developed a project starting from MQTT-SN example available in SDK for Thread and Zigbee.
I noticed that publishing and subscribing requires calls to functions...
hi，
I work in the nrf5_SDK_for_Mesh_v4.1.0_src. I want to adjust TX power based on light switch server . After setting TX power, I find that RSSI varies from high to low...
Hi.
I'm using nrf52840 SDK 16 with S140.
in my last piece of code static arrays were not enough and i needed malloc.
I used malloc without any issue, also i use cJSON...
Hi I am new to BLE energy and I would like to know if there are any SDK examples I could refer to learn about two DKs to communicate the external sensor data to the central...
Hello Nordic team,
I'm working on an nrf52840 with the SDK 15.3.0.
I'm using the SPIM instance 3 at 32MHz to interract with a Slave SPI which can support up to 40MHz....
Hi my USB keyboard application works on Windows and Linux but not on a MacBook Air with macOS Sierra 10.12.6. So I did step back and tried the combined HID example nRF5_SDK_16...
Hi,
I am using NRF52832 on SDK16 and Mesh 4.1.
When I use the NRF Mesh app to connect to a node, everything just works fine. Whenever I reset the device, the app and...
Hi,
I want to use a timestamp in my payload when ever I send data to the cloud.
First I wanted to use the ntp example from Håkon found here: https://github.com/Rallare...
So I've been tinkering with nrf2401 module lately and trying to send data between the modules. PTX is set up on STM32 and PRX on RPI, and i'm sending from PTX to PRX.
I...
Good Morning,
is possible to have a manual nRF Connect for Mobile to evaluate the features of your App ?
If I see well, there aren't features to browse the folders...
After updating the J-Link firmware, I found that PAC10100 doesn't work, but I can't reprogram it, so I would like to ask the following questions
1 Will upgrading j-Link...
Hi Team,
We need conditional compilation between crypto engine related macros for CC310 and mbed TLS and micro-ECC.
If we add our own macros in "sdk_config.h" file we...
Hello,
I need to develop software that realizes the following communication.
[For Central]
Communicates with two peripherals with 2Mbps PHY(short range) and long...
