Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi,
I am using NRF52810 which acts as a peripheral to send data to the central . The problem is my device is battery operated,So advertising all the times consumes battery...
Hi,
I have Design a new product based on the NRF52840 I am trying to get the lcd up and running so first thing is the pwm for the backlight. I am using pin 1.08 for the pwm...
Hello everyone, We're using a NRF52840 dongle for a Uni project. We got a couple of dongles it. I stupidly used a image on google to know the pinout because it's hard for...
I am trying to use the BluePy Scanner on a Raspberry Pi 3 B+ with a nRF52840-Dongle programmed as a Bluetooth: HCI-uart .
I am able to get the Bluepy Scanner code to work...
Hello,
I have nrf52DK and I want to deploy templates from S130 protocol to NRF51822XXAC. Any tutorial or guidance would be greatly appreciated.
Thanks in advance.
Hi to everyone!
I am working on the SDK 17.0.2 and my project contains nrfx_twim.h functions.
I have a problem to understand the changes that i have to make in the sdk_config...
hi..
I am using nrf52832 and 15.2 version sdk . my laptop 64 bit wndows , there is no software for 64 bit windows , so i installed the 32 bit software
i am getting the...
Hi, I'm just wondering if there could be any chance that the GPIO can be used as ADC? I had my gas sensor output wired to GPIO (P0.03) instead of ADC (AIN0-AIN7) pins. TIA...
Hi,
I tested UART app(nRF Toolbox) by iPhone for scenario: erased bonding info of peripheral but iPhone, then establish connection between iPhone and peripheral.
Here...
I am trying to integrate code on hts221 with an nrf52832. I am using sdk15a for referring the .h and .c of hts221.
NRF_TWI_MNGR_DEF(m_nrf_twi_mngr, MAX_PENDING_TRANSACTIONS...
My programming environment ：nrf52840, nRF5_SDK_15.2.0, armgcc
It shows that MD5 is avaliable in the nRF sdk documents, and I actualy run the hash(SHA1, SHA224, SHA256...
How to set the associated registers of nRF52840 for Ble_LR125Kbit and Ble_LR500Kbit modes. The following configuration did not lead to successful communication. Please help...
Hello Community, I have done some of the programming for nrf52840 for custom ble,interacting two ble devices as master and slave,etc now i want to move on to ble mesh networking...
