Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
Update:
Module: nRF52832
SDK v 14.2, SD v5.0, windows platform
I am trying to write to save a value to UICR customer register. My routine for saving the value...
Hi,
I am trying to use bootloader and following https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
In Step...
Hi,
We're currently developing a low-power framework for the nRF52840 and testing the application on a Dongle configuration. We have no problems when supplying the chip...
Hello,
This question is referring to the ability to obtain a rough location without using GPS based on the location of the LTE tower that you are connected to. The idea...
My apologies if this question is not appropriate to DevZone, but I am supposing there may be some relevance, and possibly someone with a similar problem. I have made a web...
Hi Nordic Team,
Please suggest the variables or parameters to be enabled to perform scanning and advertising in the sdk_config file. Please help as soon as possible.
Thanks...
Hi Nordic Team,
I'm using nRF52832 DK.
Please suggest any example code to read GATT service(Device information service) by a central device. Please help as soon as possible...
Hello, recently i have my computer changed to a new one with Windows 10. So yesterday i have performed an fresh new install of NCS and Segger with [ Getting Started Assistant...
Hello, I am compiling an application to be flashed onto a nRF52810. I am using Segger Embedded Studios and the nRF52 DK to develop the application. I want to read values from...
Hello All,
I have nrf52810 chip. using softdevice 6.1.1
I have implemented dfu feature.
Now i have implement tx power change feature through nrf connect mobile app...
Me and my team have been working for a couple of months on a custom firmware code for nRF9160 on a custom PCB, based on mqtt_simple and asset_tracker which basically reports...
I have been working to get the secure_bootloader examples to run on the NRF52832_XXAB (QFAB with 32kB RAM and 256kB Flash).
Apart from the fact that I had to change the...
Hi,
Good day!
Problem statement:
TSM12 Capacitive touch sensor IC (I2C com supported) is used in our application. It has got 12 output channels and Channel 1 is a parallel...
I am trying to send a string from the board through uart to the PC(windows) through usb-ttl. I tried using adruino and was able to successfully execute it. but when i tried...
