Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello,
I am using UART1 to communicate with sensor. It is working fine. I can receive the data. Now I want to modify this data. When I use strcpy() function, it works properly...
Hi Team,
We are trying to make Nordic NRF52840DK board to act as a server (BLE ) where as we are trying to connect other board (Not the Nordic chip) has only transmitter...
Hello again, I accidently verified one of my own answer so I will retry.
I am currently trying to update the firmware for Thingy 52, using the NRF52 development kit. ...
I'm using a nrf52840dk as peripheral and iOS (iPhone 8) as a central. They are to be paired. The pairing routine is already implemented and works fine. The problem is that...
Update: Was me being a dumb ass and calling the advertising start higher up in code that I thought I disabled. After truly disabling the BLE, I was able to debug and found...
Hi,
Overview: In our board BMD340 (containing nRF52840) module present with GSM module and they exchange data using UART(PINRX-6,PINTX-7). Now we trying to use "ble_app_uart...
hi,
i am using one central and 18 peripherals. i am unable to send data to one particular peripheral from the central .plz help me to identify a peripheral in the group...
Hello, We were interested in a new SoC nRF5340, but I would like to determine some points in advance:
peripheral blocks remained the same as in nrf52840. Or were changes...
Hi there,
I would like to add the device address of a central to the whitelist on my peripheral. Is this possible without bonding? So I set sec_param.bond = false in pm_sec_params_set...
Hello.
I am working on ble project and using uart communication between bluetooth and stm32. I need to reinitialize uart module in case of any error in event handler but...
1、nRF52830。Does the dongle included with the product support the over the air packet capturing function of Bluetooth?
2、We need Bluetooth to grab packets. Do we need a third...
Hello,
nRF52840-DK
SDK: 15.3.0
s140
OS: Ubuntu
IDE: SES
Our application is has a notify characteristic that works when attached to the JLink debugger. I can get...
Hi, I am using nRF51822 on my custom board with SDK 12.2.0. I use DFU bootloader, and can update application in BLE from DFU mode with bootloader (dual bank mode is used)...
I am using the nrf52 Dk with nrf52832 chip and i want to write bulk data onto the dk and then when i read the dk from the mobile app nrf connect, i want to see the written...
Hi,
I am trying to integrate the DFU service into the ble_app_uart example. I am using NRF51822 with SDK 11. I was able to successfully run the ble_app_hrs with dfu. So...
