We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I have a requirement for BLE and 802.15.4 stacks in a multiprotocol environment. I have looked at the sample at NordicSemiconductor/nRF-IEEE-802.15.4-radio-driver on github...
I am trying to initialize the RTC and trigger an interrupt every 10 seconds, and I am unsure of why the code above is not working. I followed a similar method to initialize...
Hi,
I'm working with the nrf52840 and spi mngr to talk to a SPI flash memory (AT25SF081). I use nrf_spi_mngr_perform to send a command to read the manufacturer ID
...
Hello,
I am having some trouble attempting to advertise a single custom 128bit uuid. I have two custom services sharing the same base uuid. Everything works correctly after...
I am trying to add major minor values in the ble_app_hrs example in SDK_15.3.0. I am getting an error code of 12 which is invalid data size at:
err_code = ble_advdata_encode...
Hello,
I am using SDK version15.20,pca10056,s140.
In my application I am using Bluetooth to send the data values at the rate of 750 samples per second. By sending 3 set...
Hello,
When performing serial communication using UARTE in the environment of SDK 15.3.0, SoftDevice 6.1.1, In rare cases, abnormal data is received. I don't know the cause...
Hello!
I am compiling the fiirmware for Thingy:52 (version 1.0.1), using the following link:.
https://github.com/NordicSemiconductor/Nordic-Thingy52-FW
nordicsemiconductor...
Hello All,
I've recently run into an issue with the nRF52840 Dongle where the Green channel for LD2 is not lighting up, this is a problem that is persistent across all...
Hello Nordic team,
In our project we have a requirement to write a log record to flash sector when any fault occured (hardfault or SD fault callback), so we can download...
I want to transfer data from slave to master and back to slave from master and I am doing this in the following cases: 1) Case1: Fixed connection interval and slave latency...
Hi,
I hdd developed a ble product based on nRF52810 ( SDK_15.3.0_59ac345 s112 ). I had set the connect paramter like this:
MIN_CONN_INTERVAL MSEC_TO_UNITS(150, UNIT_1_25_MS...
Hi,
Do you have a better example than the one on nRF Cloud that can show me how to transform a HTTP GET /message from my thingy. Right now, the messages are nested and it...
While I know the 9160 does not support voice calls, I would like to know if the 9160 will accept mobile terminated (MT) data calls. If so, how is that represented in the firmware...
First of all , p lease forgive me for m y bad English if it annoys you .
I do have an interest in nRF52840 development kit, because I am trying to find a development kit...
