I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
My current project make use of pairing/bonding and at certain times I change the attribute table. To notify the central device about this change I have added the Service...
I am working on NVMC. I was going through the product specifications for the NVMC. In that, it's given that the number of write operation limit is 181 for a block in nvm....
I'm trying to get the PPK working when connected to aNRF52840-DK, but getting the error - Error while setting up device [REDACTED_SERIAL]: Error occured when close opened...
Hello Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0 in my customboard.
As peripheral, device communicate Ios phone by using ble.
However, my device sometimes...
Hello. my name is Alan. I'm a newbie about BLE bonding.
because our new project needs a bonding feature, I referred to the Heartrate example(ble_app_hrs) to apply bonding...
I am working on ble_app_blinky trying to add the capability to transmit data to another device(e.g Arduino).I have already enabled APP_FIFO_ENABLED ,APP_UART_ENABLED and UART0_ENABLED...
How to add uart peripherals to mesh. Thank you very much
How to add uart peripherals to mesh.Thank you very much
How to add uart peripherals to mesh.Thank you very much...
hi
In mesh 3.0 sdk, why does the lpn example only enable PB-GATT.
Only PB-GATT is turned on, is the device only sending GATT broadcast packets.
However, I now need to...
hi
In mesh 3.0 sdk, why does the lpn example only enable PB-GATT. Now,
I need to make a product. Support PB-ADV. And it is an LPN device. What should I do?
I am using...
Hello,
We are currently evaluating the Bluetooth Mesh solution for our product-line that consists of a Bluetooth Gateway that can communicate with battery-powered devices...
Hi All,
I am using light_control example from Mesh SDK and I need to get something that identify my device in mesh e.g id, address. I would like to send some message to the...
Hi,
This is somewhat tricky question.
In my custom board application program using nRF52832 chip,
I used uart initialization function (e.g. uart_init()) and printf...
Is it possible to use a Nordic nRF52840 DK and a personal BLE board to run the throughput example? What types of modifications would have to be made to both boards?
Hi,
after setting up the LPN-example like described here I can establish a frindship relation.
When I measure the current I can not get lower than 40uA.
I use a Multimeter...