Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi Nordic Support,
I am measuring the low-power current consumption of an nRF54L15 DK using a Power Profiler Kit II (PPK2).
In the nRF54L15 DK / Nordic documentation,...
While developing my project, I need to receive UDP packets with the NRF9151. My configuration is as follows: - 1nce SIM - VPN between my UDP service and the 1nce network ...
Hi
I use the light ctrl example from NCS 3.2.4 on the 52840DK v3.0.1, serial communication with an external MCU is required. After suspending the UART and disabling Mesh...
Hello, I was wondering when will the new nRF54LM20A/B series of SoCs will be available to build as a new board based on them? In the current version of the nRF Connect for...
Hi there. I am trying to use the RISC-V core with a custom code to take a picture. In a separate project it is working with MBOX and communicating the image pointer in memory...
Hi
I'know there already exists some tickets regarding getting the version number of the software running on the net-core but they are old and do not answer my question....
Dear Nordic experts,
I am looking for which CMSIS version are used in nRF5 SDK versions. For instance 17.1.0 uses CMSIS 5.6.0. But I cannot find which CMSIS version is used...
I want to change the BLE advertisement TX power output.
I can already do it via the prj.conf file,
CONFIG_BT_CTLR_TX_PWR_ANTENNA=-4
but I need to change it on-site during...
I am designing an ultra-low-power BLE Audio TWS board based on the nRF5340 and have followed the recommended hardware design guidelines throughout the project. This is my...
Hi everyone,
I need to implement a coded Phy ble communication in a project and for that I wanted to use an nrf52840 dk. However, for it to be able to compete with the Aircable...
Here are results of running the bluetooth sample central uart, first when built with target nrf9160dk/nrf9160, and second with build target nrf9160dk/nrf9160/ns.
*** Booting...
Hi, I am having troubles with flashing my first code to the MDBT53V module. I am flashing via JTAG cable, from my nrf52840DK using vscode. According to my measurements the...
Hi, We currently update firmware using the official nRF Connect app with a .bin file over BLE, and that works for us.
Our team needs to implement the same DFU flow in our...
We are experiencing critical data integrity issues on the BLE link of our gateway device. The problem occurs specifically when the device is operating as a BLE-to-Wi-Fi bridge...
Hi,
Any specific reason the errata Anomaly 166 : https://docs.nordicsemi.com/bundle/errata_nRF5340_Rev1/page/ERR/nRF5340/Rev1/latest/err_340.html resolution patch as present...
