Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
We are currently developing on the PCA10056 as we wait for our development boards. We would like to implement UART0 as a debug port, that we can output the log messages to...
Hi,
Can somebody explain how the Ax, Bx and Tx registers are used in the calculation of the temperature reported by the temperature sensor block in an nRF52832?
What we...
Hi,
I need to connect multiple SPI slaves in a daisy chain. It seems that using nrfx_spim_init once and nrfx_spim_xfer at each transfer is the simplest way to go using the...
hello, i want to synchronyze differents peripheral with a central thanks to the state of gpio i have this code but when i call gpiote() i hava nothing in return why ?
void...
I have done some reading on the forums and have seen that Martin Bohrs-Lind has ported the EMDv6.12 to SDKv14.2 and the nRF52832, here . I have keil v 5 compiling his work...
Hi
What would be the best way to interface a wireless charging circuit with a nRF52 device?
I've found a IC from Texas instruments that does the job, but is it safe to...
Hello,
I am using sdk12.2.2 and nrf52832 customized board. I am putting mcu to sleep mode using sd_power_system_off. Now when I am pressing button for first time I am not...
Using the include files and .dll file from
www.nordicsemi.com/.../nRF51822 -> "DOWNLOADS" -> "nRF51-BLE-Driver-Win" I have created a C# wrapper for the driver. I works so...
Hello,
I'm using multiple GPIO pins as inputs. Should I use nrf_drv_gpiote_in_event_enable() for each pin? Also how to configure the input_event_handler() to handle the...
Hello,
I'm a beginner on BLE protocol and i would like to send data during approximately 4us,stop it during the same time and transmit signal again during 4us and so on...
Hi
I’ve downloaded nRF5_SDK_11.0.0_89a8197 and starting with examples from \examples\ble_peripheral\???\pca10040\s132\arm5_no_packs\
I'm writing an application to be running...
Hi
I am new to ARM and Nordic programming.
I want to send one HEX byte via SPI.
It works with some HEX numbers and with some numbers it wont.
0x13 / 0x15 work
0x14...
I wonder if it is OK to change the lpcomp ref input on the fly, without any other stop task or disable/enable. Just like this:
//--------------------
static void lpcomp_set_ref...
i want to print the data to the uart to see the values in the uart..i am unable to initialize the uartt..
what are the things to be added for the initialization of the uart...
Hello I need to increase the maximum number of servers for clients to 100. I saw that in the light_switch_example_common.h file, the definition #define SERVER_NODE_COUNT ...
