Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello,
It has been a while since I have done any controlled impedance and was wondering if someone could provide me a quick sanity check before I continue:
Here is the...
Hi,
Does nRF52840 support stable modulation Characteristics
It is found that Stable Modulation Characteristics fail during the test, and the capacitor of the debugger...
Hello everyone,
I'm using nRF52832 with SDK v17 (S132 Softdevice).
I don't know why, but I can't disable softdevice. I can enable it normally, but when i make use of...
Hi,
I’m looking to monitor LTE-M or NB-IoT packets sent by the Thingy:91 in real-time using an app or software. Currently, I’m using the Thingy:91 to send temperature logs...
Dear devzone,
I followed this instruction to use nRF54L15-PDK v0.8.1 to burn external boards. The wiring diagram is as follows:
Command line input: nrfutil device recover...
I have a Minew MSR01-B milimeter wave sensor and I would like to know if there is any nordic hardware that i could use to comunicate with MSR01-B sensor, get the data and...
Hello,
I am designing a battery monitoring circuit for a 3.0V CR2032 coin cell using the nRF52840, and had some questions. I am following the battery monitoring circuit...
Good afternoon,
I have successfully established a 2.4GHz Zigbee network using nrf52540 + Zephyr + ZBOSS. Now I need to switch to sub-1GHz band - suits better my application...
Hello,
I am trying to implement BLE DFU with nRF7002DK and SDK 2.7.0(Sorry but not use sysbuild yet.)
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
Hi! I'm trying to find examples for a use case we might be exploring. Specifically, we'd like to connect an nrf52833/20/other to an Ipad over a USB HID interface. The connection...
I am trying to work through the Dev Academy - nRF Connect SDK Intermediate - Lesson 3 Exercise 1. I have run into a problem in step 8. Everything prior has gone OK and I successfully...
New nRF5340 DK board - PCA10095 2.0.2 2024.32 1050055047
HP Laptop with Window 11
Installed nRF Connect for Desktop v5.1.0
DK board is detected
Attempt to program...
I'm trying to make a template project tidier while waiting for an answer to a question and have removed a load of functions from main to serial.c but VSC is telling me
it...
Hi,
I believe there is a significant inconsistency between the documentation and implementation of AoA antenna switching in the nRF Connect SDK. My testing of this was done...
