Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi,
I am trying to run the ble_app_hrs on my nrf51822 based board in combination with the nRF51822 Development Dongle. I am following the instructions from nRF51822 Development...
How can I add PKT_TYPE_INIT (DFU Contorl Point - OpCode = 2) into my DFU?
S110 nrf51_sdk_v6_1_0_b2ec2e6
Chip nrf51822
Softdevice s110_nrf51822_7.0.0_softdevice.hex...
I have a nRF51822 chip sending me BLE UART data to my phone and it works fine with the app. No I want to send it to my PC and Read the data (and send commands) via PuTTY....
Hey guys, I'm looking for a printed antenna PCB file. I have already read the white paper and I think using a more complex antenna would save more space and increases the...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
MCP and iOS are generating a different event sequences for a long writes.
MCP: after the BLE_EVT_USER_MEM_REQUEST...
Hey, I noticed that most of the wearable ble devices (without keyboard and screen) on the market are using 'push to confirm connection' authentication, when you have to push...
Chip nrf51822
S110 nrf51_sdk_v6_1_0_b2ec2e6
Softdevice s110_nrf51822_7.0.0_softdevice.hex
I use "nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\pub\device_firmware_updates...
Hi,
I am trying to set up a custom service and I have it all setup and it works properly. The only problem is that it is advertising as a 16bit service. I am moving from...
Take into account an application on the nRF51822 and S110.
I have defined different custom services, so UUID is 128bit long.
When advertising:
Is it advisable to include...
What are the mechanics of using 'uuids_more_available'? Is this list transmitted as a part of advertising data, scan response data, or both? How does the host know that this...
I'm using mbed+nRF51822+BLE_API+softdevice 7.1.0 for BLE peripheral side. I add uart service with the setting BLE_GAP_CONN_SEC_MODE_SET_OPEN which is open link, and set the...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi
While browsing the new files in the SDK 8.0.0 i had a look in the new ble_advertising module. In the start advertising function the pstorage access is checked if it's...
