Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hello I have been able to run the lvgl sample in the nrf9160dk, however this only works when built in a secure board, when build in non secure a bus fault occurs. Using the...
All of our wireless products over the past 10 years have used the nRF24L01 or nRF24L01+. In order to minimize latency for our time-critical communications protocol, we are...
Hello,
I am trying to program an nRF9160 chip using pynrfjprog v10.15.2 and JLinkARM.dll version: 6.88 with a Segger Flasher Compact. This flasher supportd the nRF9160...
Hi,
I need to know on how to work with asynchronous SPI for my application use case evaluation, However i found no sample/example projects demonstrating the use of nCS...
Would it be possible to know a little bit more about the onboard integrated RF52-DK Nordic Board Antenna please? What type of implementation is used?
Kind Regards,
Za...
There is another case, where someone else pointed out the same issue but I can not find it. Anyway there was no solution.
When using VSCode with NRF Connect SDK installed...
Hi
can you help with this? Setup: MoSh example running on nRF9160DK
There appears to be some sporadic «Old AT event handler : %CESQ xx,y,zz,n » notifications with the...
Hi, I am working with the Thingy91 development board. Currently, I have flashed SLM on nRF91 and I am using nrf52 as my "main" processor for sending at commands to nrf91....
Hello Nordic
We have a device, working on nrf52832, with s132 and nRF5 sdk11.0.0, at customers around the world.
It contains a bootloader mechanism that copies a received...
Hi,
I am not able to use the gpio pin p0.18 as a gpio with nrf connect sdk.
I have tried to toggle the pin using "gpio_pin_toggle" and gpio_pin_set" functions but...
Hello, I am trying to make a connection between NRF52832 and ESP32-S Module using BLE.
I implement a simple client application to ESP32-S and I can handle read,write and...
Dear Nordic team,
considering our error analysis, does the nRF52840-CKKA-F have an internal error flag that is set when the external LFCLK source is absent or shortcut?...
Evaluating nRF53 PDK. Trying to build basic samples from zephyr repo as advised here - https://devzone.nordicsemi.com/f/nordic-q-a/54451/nrf5340-support-in-nrf-connect-sdk...
Hello,
maybe it is a very simple question but I didn't figured out the answer yet. Is it possible to start MCUboot from the application firmware code (to avoid pressing...
I have 20 advertisers. I have nrf sniffer hex flashed in one nrf dev kit and i am using wireshark.
I intend tht sniffer should scan only those device whose address i will...
