We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Respected Sir/Ma'am,
I have attached my schematic below.
I need to perform Offset calibration operation for which I need to control the SCLK value.
I am sending...
board : nRF9160DK
SDK : nrf connect SDK v1.5.0
sample : \v1.5.0\nrf\samples\nrf9160\lwm2m_client
Hi, i am testing lwm2m_client example and
Q1. i dont know how...
I'm trying to implement an immutable bootloader + MCUBoot + (SPM and APP), and then update the app via fota.
My implementation is based on the asset_tracker_v2 example....
Hi,
I'm working on an app where I need to collect data from a sensor, and send it over NUS every 10ms.
I'm using nRF5340-DK (0.11.0), and I'm using nRF Connect SDK v1...
Hi,
I need help to clarify the API for IAS zone server. If I can get example implementation, it would be great.
I have hard time understanding how zb_ias_zone_app_callback_t...
Hi,
I am new to nRF9160DK . I want to set RTC time for the nRF9160DK.
In the application we are getting UTC time from NTP server and we need to set RTC .
I have referred...
Hello,
I am trying to get my nRF9160 to connect to a https server via AT commands, but this is as far as I've been able to get.
In the end this will be used in a project...
Custom board, ncs v1.5.0, modem FW v1.2.3, SES v5.34a. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to a private...
Hi guys, I'm struggling on multiple fronts to make the system building up again after NCS upgrade to 1.5.0. This is the last uncanny warning I get at build time. Please give...
Using SD S140 7.2.0 SDK 17 (nRF52840).
I cannot write to internal flash addresses above 0x78000.
I am calling nrf_fstorage_init setting start_addr=0x68000 and end_addr...
Hello,
I am looking at the TX start-up current for the nRF5340 mentioned here (last 2 entries in the Radio current consumption (Transmitter) table) in the product specification...
Hello,
I am having an issue where I am trying to send a payload in the ACK in the ESB protocol. The issue is when the PRX gets a payload it was not expecting (i.e anything...
Hi Nordic team,
Please guide to resolve the error .
While trying to convert the model_handler.c to model_handler.cpp the below deceleration shows multiple compilation...
Summary: What are advantage bullet factors of Zephyr RTOS over FreeRTOS to choose this in nRF Connect SDK v1.5.0
Details: We have Implemented our previous project...
Due to a particularly stupid thing I have done on another chip, I have ended up depending on the ability to advertise a short name and a long name. However, when I build an...
