Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Dear
I am trying to locate the data area of application code from device (nRF52840).
From here , it show me the bootloader will locate at from 0x000 F 8000 – 0x000F E000...
I've been writing a vendor model for Bluetooth mesh based on the light lightness model in the SDK. I'm extending the generic level model into my model - a window openess level...
Hello -
I am trying to set up the nRF9160 DK kit. I successfully updated the firmware and entered the ICCID, PUK, IMEI, and HWID values. When registering for nRF Cloud,...
Howdy,
I'm trying to get Zypher up and running with the Particle Argon board using the nRF52840 chipset. The goal is to get both Bluetooth and UART working, but for now...
Hi all,
We are using nrf52 DK (both pca10040 and 10056) to develop a multi-channel ADC sampling module running Mynewt.
The example ADC code with Mynewt is a single-channel...
Hi All,
I am in the process of fabricating my own PCB for the first time using nRF52840 chip.
The design will be somewhat similar to the nRF52840 Dongle design with slight...
Hi All,
I am trying to simulate the nRF52840 Dongle Antenna given in the hardware files using CST studio. I am using the following substrate and trace width which was in...
Hi All,
I am trying to write a driver for the Grove-LCD RGB Back-light V4.0 using nRF52840 DK. However, it doesn't work. I am trying to figure it out why.
The description...
Hello, I'm a beginner who just entered Nordic.
It may be difficult to read because I am not good at English. Please excuse me.
I use NRF52DK and SDK v17, and I'm developing...
Hi guys. I'm currently stumped by a most peculiar issue.
Im using two PCA10040 boards (20 cm apart) to send a data stream via the GZLL protocol: DEVICE button pressed -...
Hi,
We are talking with a Bluetooth certification provider regarding our product, and need QDID's for Host and Controller.
The nRF52x is running Zephyr and the Host is...
We are currently developing an application for nRF5340 using the nRF Connect SDK which requires bluetooth mesh + iBeacon coexistence. Are there any resources/examples available...
Hello,
Can broadcasting be set to unconnectable mode to reduce power consumption? I tried to set the broadcast to p_advertising->adv_params.properties.type = BLE_GAP_ADV_TYPE_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Dear community
In an attempt to implement an LTE TCP client, I'm stuck at the problem, that `recv()` doesn't return after the server has closed the connection.
My test...
Hi All,
in Segger Studio those project explorer "code' and 'data' columns that pop up every time you change something are slowly getting at my nerves. In my humble opinion...
