At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
there is a module in the skylab project on the nRF52832 chip and it does not agree with the tablet, which is old BT. Is it possible, through the firmware or SDK, to downgrade...
Hi
After nRF Connect for desktop was upgraded to v3.6.1, programmer application cannot recognize all DK boards, including PCA10040/PCA10056/PCA10090.
It showed the error...
Can I use nRF21 in GPIO mode (not SPI) using the PA/LNA assist feature of the S112 soft device?
Per section 5.3 of the datasheet, it seems I could wire the PDN pin to be...
Hi,
I am learning how to write and read from flash memory on nRF52833 dev board for a BLE application.
I followed the heart rate example as shown in https://devzone.nordicsemi...
I am writing an application for the nRF52DK which uses two additional push buttons besides the 4 already present on the board.
Using GPIOTE the detection of the button press...
I have a working project that uses the NRF_LOG module to send debug outputs over the UART backend. When just using the logging module everything works correctly.
I added...
Hi,
Is it possible to set multiple APNs in nrf9160 and with fallbacks to next APN if one not working?
Suppose if we set 2 APNs at CID=0 and CID =1 positions using AT+CGDCONT...
Hello I am trying to execute the functions of SPIS and thread on nrf52840 Refer to his code to write nrf52840 SPIS: https://devzone.nordicsemi.com/f/nordic-q-a/68854/nrf5340...
Hi,
I am trying to configure the nRF Connect SDK on a Mac running Catalina for the first time and have followed the nRf Connect v3.6.0 - Getting Started Assistant.
I am...
I am new to the Segger Studio and nRF52840 . (However not a Newbie to Microprocessors)
Off the Bat :- Blinky example works fine...
.....however when I try to get the PWM_driver...
Hello, I wanted to know do this chip ( nRF52810) has both tag (beacon) and receiver function? If cannot is there any other Bluetooth chip suggestion? My main idea is to use...
I am new to Arm and Nordic devices and I am trying to port the Thingy52 firmware to SES so we can add some additional sensors.
I have got the Thingy52 firmware to compile...
Hi Nordic Community,
I follow the below link to create an openthread border router. I successfully send sensor data on things.io.
https://infocenter.nordicsemi.com/index...
