Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hello,
I have a central and Peripheral beacon on nrf52832. I am usıng nus services on both devices. After the data transfer I call the
ıt works fluently on the central...
I have been using CrossWorks for a while for multiple vendors MCUs (sometimes in the same project on the same PCB). I'm looking at using nRF Connect SDK and see that SES is...
I'm using SEGGER Embedded Studio with nRF5 SDK v16.0.0.
For the purpose of high-speed data transfer, I've searched about the BLE throughput.
Now, I want to figure out...
Hello
PWM and I2C are being used on a custom board using nrf52832. I connected I2C to pins 26 and 25 and PWM to pins 27. But I2C doesn't work, and PWM does, but there's...
Hello,
I search a NORDIC example (RF52832) that is bonded with a battery CR2032 as power supply runs very long (> 1 year).
Bonded with whitelist
Bonded with one or...
Hello,
I want to create/compile a (Nordic) secure bootloader with serial output.
I know the example of the dfu secure_bootloader. I also know there is a nomal and a debug...
I am using NRF Connect SDK on NRF52840 Dongle and I have written two programs. First acts as bluetooth peripherial device, second acts as bluetooth centeral devices. I have...
Hello! So I'm working on a project where I try to connect the nRF9160 DK to the google cloud. I tried to manage this by following this guide: https://devzone.nordicsemi.com...
Hi,
I'm using the BLE app (ver 3.6.0) in nRF Connect for Desktop together with a PCA10056.
I'm scanning for a device that sends three ADV_EXT_IND, one on each channel...
Hi,
I am using the USB CDC example in my project, where I developed my own application level communication protocol.
I have a problem with the data throughput, it's...
I am designing a custom board with a nRF52840 module that has no 32.768 kHz crystal embedded in it and as a first step want to test it with some examples that use only RC...
Hi all,
I'm trying to setup an interrupt-driven UART. UART is able to transmit data, but I don't get the TXRDY interrupt.
Below is my minimal initialisation that outputs...
I developed on sdk16.0 and found that app_button has abnormal power consumption,
so I replaced it with app_button of sdk15.3, but found that no key events were reported...
I want to use UARTE to handle terminal style messages. That is, messages are ended with a newline, I have absolutely no idea how long they will be, and the delay between multiple...
Hi there, Just wondering how to get the comparator "RESULT" (not part of EVENT) onto an output pin without CPU intervention. From the datasheet I believe: 1. the RESULT is...
