But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Greetings,
We developed a customized board using NRF52832. We flashed the code using NRF connect JTAG. The LED is working fine. But when we flashed the BLE_UART BLE is not...
Fired up nRF Connect v3.6.0 on MacOS
Plugged in new 9160-dk and switched on.
Connected to USB.
Selected board. Green dot appeared but nothing in the "Device memory layout...
Good morning,
We have developed a prototype based on the nRF52840. We have also developed an Android application.
When smartphone has device already bonded the application...
Hi,
I am a beginner in BLE Mesh. I am trying to create a Mesh network for residential purpose using Tuneable lights, switch and sensors.
Mesh SDK version : 4.2
On the...
Hi, I am developing a SDK 17.0.0 based iBeacon application, and I see below API for initializing/updating advertising data.
I want to know what does it do with the buffer...
Hello
I am now quite familiar with the basic PWM playback capabilities of nRF52832. However, I would like to make a chain of simple and complex PWM playbacks.
I have already...
Hello,
I am developing an application that sends data from an Arduino Nano 33 BLE Sense to a custom Android app (Motorola Edge running Android 10). The Arduino board is...
Hi,
As many of you, I'm tryng to compile pc-ble-driver (v4.1.2) found in https://github.com/NordicSemiconductor/pc-ble-driver/tree/v4.1.2 , just to see how the code works...
Our application stores sensor data in flash and sends the data on request via USB. But if the device is connected to Bluetooth once then it is having issues in USB data transfer...
Hello,
At this point I have been able to successfully customize and run the mcuboot procect.. Mcuboot is successfully built and linked with my app.
However I am would...
Hello
I'm Strangistra and I work on a Adafruit Feather nrf52832.
I have the Arduino IDE 1.8.13 and I use the FastLed library 3.3.3.
I have a strange behavior with the...
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.1.0/nrf/samples/bluetooth/peripheral_lbs/README.html
I'm talking about the above. SW5 switched to nRF52. However...
My team is trying to acess OpenThread CLI over UART0 with the nRF Connect SDK OpenThread CLI sample with our custom board.
We have tested with a Nordic's nRF52840 DevKit...
Hi,
I'm using nRF51 dongle as a sniffer and executing 'nrf_sniffer_ble.bat' file via cmd. I have tried interface commands "nrf_sniffer_ble.bat --extcap-interfaces" based...
