This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
hello ,
i am working on recieving data from sensor using nrf52832 with time and data right now i am getting time that is set by me my problem is i have to set time automatically...
Here is an issue I am having when using MQTT in a poor (RSRP < 15) LTE signal environment
Condition:
nRF Connect SDK v1.3
modem firmware v1.2
TLS Socket is configured...
I've worked through the Custom BLE Service example ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ) and I'm attempting to port it to C++ to form the...
Hi,
I need to write a linker (ld) script for our nRF52 application. Essentially I need to combine the linker script that we already use with the scripts that exist in the...
trying to build a long range coded phy broadcast/scanning application. as I know zephyr doesn't support that so we have to include nordic link layer based on this post
https...
Hello all,
i am using ble_app_uart example.I add the line
in the begining of the main function. All the ble connection works, but putty shows strange characters...
I am having a bit of trouble getting high enough data throughput for my application so I have a few questions regarding it.
Can running the spi/other peripherals affect...
Hi，
I tried to build a BLE sniffer environment. And it works well to capture the LE secure connection air packet after Eable Secure Connections debug mode （uses the debug...
Hi,
using:
SDK for thread and Zigbee 4.1.0
NRF52840dk
I am trying to add UART (for my custom application) to an existing Thread example with CLI. (e.g. ble_thread_dyn_hrs_coap_srv_freertos...
Hi,
I'm really struggling with encryption, kind of lost in the woods of libraries, api's and documentation. Can anyone point me in the right direction?
Config: I have...
Hi support team,
i'm trying to build sercure bootloader on beacon nrf51822xxaa. I used SDK 12.3, here is my config
and i use nrf program to read flash infor
when...
Hello,
I am working on a Proteus III module which work with a nrf52840 SoC. I am using nrf52840 DK to test and develop code and at the same time testing the codes in the...
Does the nrf_cc310 support interrupt operation? I want to start the calculation of a hash/asymmetric signature but don't want that the CPU busy-waits until the calculation...
Hello,
I am trying to do make a connection with sd_ble_gap_connect();
First i am scanning all the devices arond and i am filtering with my functions using with ble_gap_evt_adv_report_t;...
