I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I know there is Current consumption common conditions in the datasheet. (table19. nRF9160_PS_v1.2.pdf)
There is VDD level but It's not described the VDD_GPIO level.
1...
Hi,
I am following the tutorial https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/getting-started-with-nordics-secure-dfu-bootloader...
Hello,
I really find this tutorial useful and substantial. I followed the steps in downloading the github projects but I got the following errors when compiling (Note: I...
Greetings everyone,
I am a beginner in this and would like to ask for help in reading battery level.
Battery info: 3.7V, 100mAh, 0.37wh.
I have tried to read on the...
hai ,
i my application i need to update ota over serial . i m using nrf52840 and sdk 15.2
step 1 : at first flashed uart boot loader code on my board
step 2 : updated...
Hello
I am testing connection between nrf51 dongle and my BLE keyboard using heart_rate_collector sample.but there is an issue with on_service_discovery_response.
my BLE...
Does exist any IC/module of Nordic which could be used as NFC reader/initiator and that has BLE integrated also?
Or just a little BLE module with on-board uFL connector...
Hi Devzone:
We are testing TX and RX range with our customized boards, and encountered a rather bizarre problem:
The connection range is pretty good indoor, maybe 20~30...
I am working on a driver for the Adesto AT25QL641 QSPI Flash Memory chip. Comparing the hardcoded nRF52840 QSPI instruction set and the AT25QL641, they are 90% identical except...
Hi,
I am trying to implement Zigbee mesh and in the Zigbee End device(ZED), I want to know its neighbor table record or routing table record. I did not found any specific...
Hi,
In my application,I have written a code based on ble_hrs sample example. When I am checking the RSSI value at the tablet at 2 meter distance I am getting -56dbm. As...
Hi,
I am planning to design my own custom PCB using the nRF52840 chip.
As I am getting started, I want to make sure all the design rule dimensions are up to the standard...
Hi All,
I am trying to design a BLE module based on the nRF52840 Configuration 6 (Only Battery) provided in the product specification document.
To get started I was using...
Hi,
I know that the S132 v6 didn't support multiple advertising sets with different advertising handles. If you want to advertise with new data or different parameters,...
Hi All,
If I am to use a Piezo Buzzer to generate sound using nRF52840 PWM:
1. any suggestion on how to design the circuitry?
I am planning to use a Murata cimponent...
