Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
In our setup several devices are suddenly not working anymore, power off and power on is not working. However, if I connect the debugger it suddenly starts working.
So the...
Hello,
I'm trying to compile a slightly modified version of the template application for nRF52832 using Segger Studio. I'm running into a compile issue with this line utilizing...
Hi,
In "ble_app_uart" project, the system will enter sleep mode after 3 mins.
When system enter sleep mode, the "RTT view" will print following message.
How to modify...
I am trying to open example project(nrf9160, assent tracker project) with SES V4.20a(download form nrfconnectSDK instruction)
1. It doesn't recognized header files.
2...
hi all ,
now , i need get gps latitude and longitude information.
reference nrf9160_gps.c file,it should be do it now ,
how to use driver to get PVT? ,
follow , it...
Hello ,
I use SDK 15.3 , chip is 52811
I refer to the example of 52840 "examples \ peripheral \ timer"
The following is the example code, I have not changed it.
...
Hi, I am trying to debug firmware on the nRF PCA10059 usb dongle board, through a nRF10056 dev kit by attaching a standard 10 pin header on the usb dongle at P1 & connecting...
Hi everyone
Program crashes after few minutes while trying to run two threads(GPS thread and a thread used for caculating the battery voltage) simultaneously.
Please...
Hi,
I am trying to understand how the connection parameters and settings work and how they change the throughput. For this sake, I have been experimenting with the ble_app_att_mtu_throughput...
Hi everyone,
I few days I tried run on my NRF9160 DK CC310 hardware RSA crypto functions.
When I started it at first I ran security_service demo where board run random...
Hi,
When I write a very simple USB audio device that just pass a sinuous wave created in a timer that runs at a 16KHz freq - how can I tell "someone" on the host listens...
Hi,
I'm wondering if there are any samples that show how to use sleep mode on the nRF9160. Not quite sure where to start to look for resources on this. Any documentation...
Hello,
Please check this code for BLE disconnection.When peripheral tries to disconnect from the central , it is disconnect successfully the first time but second time it...
Dear Sir or Madam,
We are currently trying to connect two nRF91 to the NRF Cloud service. We were able to activate the SIM card connected to the board, however, we were...
