Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hello!
Like several others on here, I’m trying to make a multilink nus central firmware. My Peripheral devices run the ble_app_uart example, and the central device runs...
Hello everybody !
Here I am designing a system with 3 development boards nrf52832, where a card called "central" is connected to the computer by USB and this board will...
Dear Nordic,
I'm developing an application using the NUS service en SPIM peripheral. Both of these work correctly independently. Now I'm trying to start an SPI transaction...
I'm developing IO-Link driver using UARTE peripherial.
Is it possible to get event on end of transmition with EasyDMA Tx. Event ENDTX is fired before all transmited bytes...
Segger embedded studio V4.18 appears to have a bug when it comes to printing to RTT. When I run the exact same firmware on SES V3.40, everything is printed to the debug window...
Whether I could build BLE_MESH network automatically within some BLE devices without provisioner?e.t I feel it is manual to build BLE_MESH network with the help of provis...
Hello,
for my project, I am using the module BT832A (from Fanstel) that implements the nrf52810. I am using the pin P.021 to drive a switch. The problem is that when I set...
Hello. I have a problem getting a position via GPS. My dev board is placed in a good place, but can't get a position after more than 1 hour.
I am using you new SW version...
I have been using using nRF9160 as ble gateway for uploading data from one nRF52832 and its works well. Now I need to connect more than one nRF52832 devices, has anyone tried...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hello all,
I am attempting to develop an application which utilizes a third party library for proprietary sensor calculations. This library requires the use of floating...
Hi DevZone team,
Hope you're doing great today. Just want to confirm if the nRF9160 is ready to operate in Mexico. The LTE Bands needed are B2, B4, B5 and B28. The IFETEL...
Hi,
I use SDK 10 pwm example (examples\peripheral\pwm) to modify the PWM cycle to 10s and duty cycle to 50%.
Code showed as below:
But the PWM cycle seem only around...
I have seen the datasheet of nRF52840 but I can't find that any GPIO pin used as SPIS. It says that you can configure the pin those whose value is written in the PSEL.MOSI...
Hello everyone!
I've tried to run mbedtls crypto functions which are using cc310 hardware implementation and I have partitions overlap issue.
Our main goal is to test...
