to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
I updated to v10.3.0 of the nrfjprog and mergehex tools and I've noticed that the behavior of the page erase command takes far less time when it gets to a certain region of...
Dear All,
I am trying to interface my nRF9160 sensor with the LIS3DH accelerometer.
What I have done so far are the following:
I am trying to use I2C_2
In my prj...
Hello Nordic Support,
I am using nRF9160-DK with the latest module firmware: 1.0.1, board version 0.8.3
I followed the instruction and it only works for tag v0.4.0, I...
Hi devzone!
I connected my flame detector sensor(szh-ek086) which sends data analog value to my nrf52840 DK.
To receive the analog value from sensor I used saadc module...
Hello, I'm trying to set up a series of remote scripts to test functionality on my hardware. The idea being that I can run a handler on the Nordic device and then control...
Hi,
is it possible to read/write the MX25R6435F external SPI NOR flash using Indirect Mode ( https://wiki.segger.com/Programming_External_SPI_Flashes) with Segger JLink...
Dear,
I am doing some range tests with the nRF52840 and saw that the RSSI value of the PCA10059 (USB dongle) can be more than 10dB lower than the one of the PCA10056 ...
Hello everyone, I am trying to implement a blocking wait using the app_timer.
To do this, I am starting a one-shot timer whose callback function sets an initially false...
Maximum current consumption for each of the pins in the respective modules of PWM, TWI-I2C, TWIM-I2C, TWIS-I2C, SAADC, UART, SPIM, TIMER, RADIO-2.4GHz under the operating...
Hi,
I'm trying to run the gps application off the master branch on the thingy91 and it dies like this:
It's built using the Nordic SES on windows.
Any ideas? ...
Hi all,
I am trying to connect to device with specific UUID. I am not sure what have I managed to do, below are some logs from NRF Log.
Did I connect properly?
I am...
Hello,
I am trying to run the mbdedtls example of random number generator shown here https://tls.mbed.org/kb/how-to/add-a-random-generator
I added MBEDTLS_CONFIG_FILE...
when i change the baud rate to 115200 my uart (Rx and TX) are giving me garbage out put.
so what do i need to change in my code(ble_app_uart example) when i have plan...
Dear Support / forum,
After reading the user and API guides, browsing other posts, and playing around with the ack-payload example, I think I now have a pretty good understanding...
