Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Previously I used the MQTT example and connected it to our own server successfully. However, I want to do the same for the asset tracker application latest release (v1.0.0...
HI
I am using nrf52832 modules with SDK 11.0.0, s132.
I am able to advertise and scan the devices and display RSSI and peer address.
For my project i want to display...
Hello,
I am trying to configure a UART to use in the nrf9160. I am using zephyr's uart.h
This is a snipet of the code I have right now.
Code as it is executes successfully...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
In order to send an SMS in PDU mode, I need a Service Center Address. Normally, you can find it via AT+CSCA, but this does not seem to be supported on modem firmware v1.0...
I have a central device (nRF52832/Soft device s132) that connects to two peripherals. Both peripherals send data to the central via NUS. I have incorporated the required changes...
hi guys , I'm trying to use the ble mesh protocoll for my master thesis. I need to send a message always when an interrupt on a gpio pin occur.
there's a problem beetwen...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
chip: 52832 . sdk 12.3\examples\ble_central\ble_app_uart_c\pca10040\s132,
i use this example to scan ble advistisment, i want to write some date to flash, i use flash_word_write...
Hi
I am doing a mesh application with :
--SOC:52832;
--with an AT Command Module connected UART;
--Mesh SDK :3.2;
--SDK 15.3;
in order to manage call backs from...
I built ...\examples\dfu\bootloader_secure\secure_dfu.eww ,pass,then when download to PCA10040 board to debug,but it show error" ELF/DWARF Error: Unsupported .debug_info format...
I am running custom firmware on a custom board using an nRF52832 chip. I have encountered an issue after migrating my project from SDK 14.2 to SDK 15.3. The issue is that...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
Since I migrated from SDK 13 to SDK 15.3 I can not see anymore print of NRF_LOG_DEBUG, NRF_LOG_INFO, NRF_LOG_ERROR and so on, on segger Jlink Viewer.
I have tried...
Are the following arguments correct?
data_rate <RADIO_MODE_MODE_Ble_1Mbit> or <RADIO_MODE_MODE_Ble_2Mbit> and so on.
output_power <RADIO_TXPOWER_TXPOWER_Pos4dBm> and...
