I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hello! I need to perform some radio tests on a board that contains an nRF52 SoC. The nRF5 SDK provides two ways of performing such tests, either using DTM, as specified by...
Hello,
I am using pca10028 dk. I want to know how can I change the transmitting power of ble?
My application needs that user should be able to change the transmitting power...
Hello guys!
I got a board of nRF52 with a Jlink debugger on it through a serial port and I program it with nrf-connect-mesh-official-serial-gateway-fw.hex.
However, when...
I am programming a Ble Nano device using Nordic SDK. So far I have been using examples from the ble_peripheral and ble_central directories. Now I want to run an example that...
Hi,
I used the nrf51822 as the spi master,it could send out the data, but it didn't receive the slave data.Did I miss somthing?
static volatile bool m_transfer_completed...
I'm working the the NRf52 dev board and SDK12.2. I was able to successfully load the standard DFU example and then use the NRF Toolbox on an android to load the example HR...
Hi.
I'm getting an nRF Dongle (PCA10031) set up on a Windows machine to be the BLE central that we'll use for our production line testing. To that end, I've built the pc...
The pc-ble-driver project uses CMake to generate Solution and Project files for the Windows build of the project. CMake uses absolute paths in these generated files. I can...
Working with nRF52832 and SD132-v2.0.1
Using Timer 1 at 1MHz (pre-scale 4) and 32bit bitmode CC to trigger events at a pretty wide range (from us to minutes).
I'm getting...
I am calling certain services and I can see this output on my UART listener:
0.000013 : UART Start!
0.385355 : BLE Stack Initialized
0.385581 : Peer Manager Initialized...
What would be the best value for UART buffer?
When I put it as 512 it gets crashes, below you can see the putty output
0.000013 : UART Start!
0.415937 : Handle list for...
I want to use app sched feature, so as example does, I call:
static void scheduler_init(void)
{
APP_SCHED_INIT(SCHED_MAX_EVENT_DATA_SIZE, SCHED_QUEUE_SIZE);
}
since...
Hi Team,
I need to make an application that we receive a data from a chip through UART and need to send the data to Console through another UART. Is it possible to make...
Hello,
My setup:
PCA10040 DK,
12.2 SDK
I copied the "BLE_APP_UART" example into my project folder and want to "upgrade" it with the TWI.
So I copied parts of the "twi_scanner...
