Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi Team,
What are the chances of pkt loss in case of concurrent observer, advertiser role using S130? Application is like in observer mode device need to observe some activities...
We have an nRFgo nRF24LE1 32-pin 5*5mm Development kit.
How do we program this as a stand alone application without nRFgo Starter Kit Motherboard ?
Is there any tool or...
Seeing the Log on wireshark for Central and peripheral communication after connection.
Here i am bit confused that when Connection update request is send by Slave after...
Hi, I try to access Generic Access to get device name.
So, I modified "ble_bas_c.c - ble_bas_c_init()" like this.
bas_uuid.type = BLE_UUID_GAP_CHARACTERISTIC_DEVICE_NAME;...
Hi,
I want to find Bluetooth address of the Central Device which is running Master Control Panel Application....
but after succeful connection, each time I try to find...
I am using serial communication to have data from a sensor. That sensor only can support baud rate 115200 to communicate. Collecting data from that sensor I am trying to save...
Hello Everybody,
I have read these articles on the site : article_1 &
article_2
I need to do something like that, read around 8000 sample with sampling rate equals...
Hi,
I used the app of nordic , that puts the system off in order to measure the current at that mode.
the example i used is at this link . ( system-off-wakeup-on-gpio...
Hi
I'm very new and looking at the PTR5518 breakout board. The docs below specify some of the pins:
Are the pins EN , RX , TX , RTS etc. tied to P0.08, P0.09,...
Dear Sir/Madam,
I want to use the One channel of Timer 1 for PWM generation and other channel is used to measure the pulse width of input square wave.
For above i need...
When I try to step through my code, I get a wdt event firing. I have tried setting the behaviour to pause during debug and sleep
void wdt_init(void)
{
uint32_t operationStatus...
I would like to measure BER and PER on custom board by using sample project that is included SDK.
\examples\dtm\direct_test_mode\pca10028\s110
Could you please teach...
Hello,
I'm powering a Readbear BLE nano using a CR2450 coin cell battery. The firmware application is written using mbed. How can I measure the battery level of the CR2450...
hi,
can i use timer interrupt has more than 1ms period??
#define APP_TIMER_TICKS(MS, PRESCALER)
((uint32_t)ROUNDED_DIV((MS) * (uint64_t)APP_TIMER_CLOCK_FREQ, ((PRESCALER...
