We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack. ...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I downloaded the nrfgo Sdk for the nrf24lu and nrf24le. In the projects folder there are several examples, two of which are of interest. The first is entitled "bootloader_32K...
Hi
I'm having a strange behaviour when using the TWI HW peripheral for reading from an I2C device. My application tries to read one byte from a register in a I2C device...
Hi,
I'm done with the hardware interface of my current project.
Right now I have a service running with a custom UUID, by writting this characterisitics you have access...
Hi,
I'm having the purpose to use nRF51422 /ANT to connect a relatively data hungry ANT device. The nRf51422 specs expose three programmatically available data rates : 250...
Hi,
I've written a nRF51 SWD-JTAG programmer.
I want to enable it to check for minimum softdevice version and error out if a too-old softdevice is found.
It is easy...
I want to communicate four same devices with different hosts. i know that one host can communicate to seven devices and also a device is able to speak different hosts . i...
Thanks for the response. As a test, I loaded the same code onto a PCA10004 and it seems to work as you described. A breakpoint at 217 does get triggered when it receives data...
I have been perusing the source to micro-esb, and it appears that it wants exclusive access to the NRF_RADIO interrupt(RADIO_IRQHandler) and things are designed so that only...
Hi,
i need to save an array of 50 kB on the nrf51822 flash. I only need to read the data stored in the array. I come from the PIC micro world where i simply need to initialize...
Hi,
On peripheral side i have S110 device with ble_bas service and custom base service. Both have notifications.
On centrasl side is S130. After discovering services i enable...
I want to use the pca10001 to communicate as a master to an accelerometer, but when i use the function spi_master_open i get a NRF_ERROR_NOT_SUPPORTED error. I get no clock...
Hi everyone.
I am working with nRF51 to make two BLE device, One act as cetral and another as peripheral.
I have implemented almost functions that the two devices are...
Hi,
Do all NRF51822-DK (development kit) have the same silicon build revision? If not, which distributor should I approach for the latest revision and is there a specific...
I have encountered a problem with the IAR linker where I run into a 32k code-limitaion, even though I have a licence with no limitations. According to IAR, the problem may...