At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I'm developing a new battery powered sensor device with an NRF52840 and have some thoughts about efficient power supply. The main question is: Using an external DC...
Hi,
I have opened Sample "Peripheral_hr_coded" and added build configuration.
Then I clicked on Action --> Build.
Please validate below log. Is it proper ?
Log is...
Is it possible to dynamically switch between USB CDC (Communications Device Class) mode and USB MSC (Mass Storage Class) mode on the nRF52840? If so, could you outline the...
Hi, recently I started migrating my company's firmware from nRF5 SDK to nRF Connect SDK. I have been following the devAcademy courses and so far 1. I have created my custom...
Hello, guys.
We need USB CDC ACM and UART driver with DMA to run in parallel as two different nodes in the device tree.
For that purpose, here is what we have in the prj...
This is a general question about selling our modem-enhanced products internationally. We use an NRF9160 (NB-IoT), but we have some of our devices equipped with older Telit...
Hello,
NAS-RAI (Non-Access Stratum RAI) used on NB-IoT Control Plane : on nRF9160 it was controllable via the AT%XRAI command, using the <rai> parameter :
0 – Undefined...
SOC: NRF52840
SDK : NRF conenct SDK 9.11
Application Gateway
we had end devices to join the network which is whitelisted in the coordinator ; so please can you let...
aliexpress.com/.../1005007557383132.html
I bought the above board I checked the revision information with nrjfprog --deviceversion and it was revision 1 All functions including...
I'm using the nrf52840, and I'm doing a project where the system needs to sleep for a long time, maybe more than 24 hours. Following this ticket, to go to sleep I just do...
Hi
I'm working on understanding how whitelist filtering is implemented and works in Bluetooth Low Energy. I'm currently following Exercise 2 in Lesson 5 of DevAcademy's...
Hi, We are working on power optimization for our project which uses nRF5340 board. Upon testing we observed when starting hardware timer the base level of the current consummed...
My custom board with a NRF5340 (MDBT53-1M) with LF crystal is running as a central on NCS 2.6.1.
It's connecting to a legacy device which has a BLE121LR.
NRF5340 centrals...
Hi,
I use vs code to run nRF9160 DK applications and it runs fine for a month. But recently I cannot build configuration even in an empty application . Old good applications...
