We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Greetings,
The only examples I can seem to locate of using the Coexistence Interface on nRF9160 is with the internal GPS but the documentation states that "COEX0: Input...
hi... i want to store data in flash , i will get the data periodically . Even i am writing data to flash using write command ,when i am trying to print the data which is stored...
I am using nRF52 DK.
When I do 2 analog inputs using the SAADC, I noticed that, in the SAADC callback, p_event->data.done.p_buffer[0] corresponds to the correct SAADC channel...
Hello,
I use a configuration with multiple NUS_C and NUS links. When I receive events, how to know the index ?
I have seen mutiple exemples using conn_handle but in a...
Hi teams,
I am trying to automate preferred mesh configuration for each node.
For example, if I use nRFMesh app, I should 1) bind application key to each model, 2) set...
Hi everyone,
During test with my small mesh network, I found that adding all-nodes to subscription list is prohibited by Mesh Specification.
In Mesh Profile 4.3.2.19,...
Hi:
I use the sdk https://github.com/jimmywong2003 to make a bin file and then run the command of ./UartSecureDFU ttyACM0 application.zip to updgrade in linux
It always...
Hi
if one searches the examples using the timeslot API, every application seems to do it's own timeslot cleanup. Also documentation is not very clear about this.
Best...
i am using nrf52840 dongle with uart using ble_app_interactive example,
but after commenting only uart with cli is replying with some text as shown in image .
For the...
Hi! I'm using S140 and I'm using the ble_advertising module to set up advertising.
This is my advertising_init function which is working properly until I uncomment the enabling...
This is perhaps not so much a question as a request.
The FDS event handler, type `fds_cb_t`, has only one argument, type `fds_evt_t`, unlike (say) the two wire event handler...
Hello,
I would like someone to explain to me payload for Zigbee cluster library (Zcl)
i was following this guide to control my lights:
https://infocenter.nordicsemi...
I am trying to connect to another type of board via the UART on the development kit. However, there seems to be a voltage mismatch. Are the nRF52840 development kit UART signals...
hi... i want to store data in flash , i will get the data periodically . i have merged the ble_app_uart +fstorage example . Even i am writing data to flash using write command...
