Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
In the nRF52840 Product Specification v1.1 ( HTML ) , description of the QDEC peripheral, Table 77 on page 275 ( direct content link) , it appears to indicate that the LED...
Hi,
We have an freertos based app (SDK14.2).
Recently we have added a WDT support in the following manner:
The init code initializes the WDT reload value to T+3...
hi all, i am using the uart with it's dma to transfer data into the nrf9160, but some of the data is lost in it's way. here are some examples of the loss count in bytes from...
Hello,
I'm using several nRF52840 boards to setup a bluetooth mesh network. Im using the python script "interactive_pyaci.py" to setup the mesh. The mesh is working and...
Hi, As the title asks, I am using the lte_ble_gateway example project on the nRF9160 DK. I am able to connect one nRF52840 DK to the nRF9160 DK over BLE. I am trying to connect...
We have a board that has become unresponsive to programming. It worked well to program about 4 times and then is no longer responding to the J-Link device. The application...
Hi,
I tried implementing serial communication between nrf52832 and HT1632.It didnt work.In HT1632 data sheet it has given following specifications
will nrf52832 supports...
I am trying to build the simplest nRF52 BLE Peripheral application (Lightbulb use case). I am facing below mentioned errors:
Building ‘ble_lightbulb’ from solution ‘ble_lightbulb_pca10040_s132...
Dear all,
I'd like to use 2 spi and 1 i2c at the same time. Can nrf52 support? I read some thread said that only using 1 spi and i2c or 2 spi. Please advice.
regards...
I'm using SAADC like this:
And I'm not getting the done event. I've also tried not low power mode.
If I place a breakpoint in nrfx_saadc.c nrfx_saadc_irq_handler, after...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK , and I'm trying to print floats using vsnprintf (I'm guessing the problem is the same as with...
Hi,
We are using nRF52 DK tool to sniff BLE data. We we using Wireshark plugin to interface nRF52 DK tool. nRF52 is updated with latest firmware. We keep the tool in between...
Hi,
we are porting code of our project from SDK 14.2 to SDK 15.3.0, and have encountered unexpected behavior from the fstorage module. Even though SoftDevice and BLE stack...
I'm trying to work with the PC-BLE-Driver with the connectivity firmware. I've loaded the connectivty firmware and the application appears to connect to the board. But I'm...
