Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I am using nRF52840 dongle for my development with "usbd_ble_uart" profile from SDK located in this following path RF5_SDK_15.2.0_9412b96\nRF5_SDK_15.3.0_59ac345\examples...
Hi.
I saw lots of questions but I could't find answer about BLE & flash write func.
Setup is nrf52832, S332, SDK 15.3.0.
using ble, ant+, gpio, timer, adc,
in code...
Hi Nordic:
I have a question about retart saadc. i want to restart saadc in a bsp event(BSP_EVENT_KEY_3) and it works. the following is my code:
i learned in this forum...
1. Download and install nRF Connect from Google Play or App Store. 2. Open nRF Connect. 3. Make sure that the DK is running the ble_app_uart example. LED1 should be blinking...
Hi,
My firmware is working well and handling required functions, so I have begun trying to work on power management to reduce device power draw. I am using S140 and my BLE...
Hello,
Using light switch dimmable (experimental) example, I will like to change the default name displayed by the server/client to a custom name.
See the screenshot below...
Hi,
I'm trying to receive data from a UART transceiver. I'm using a nRF52 DK with a RS485 to UART transceiver chip.
On my debug session I get the " NRF_SERIAL_EVENT_DRV_ERR...
Hi,
I have a nRF52833 DK which contains PCA10100 debugger on it.
However, examples in the nRF5SDK160098a08e2 SDK seems like not supporting PCA10100.
Which example...
Hi all, I am beginner to Bluetooth module interface and I am in the stage of implementing the software for Bluetooth module to start and visible to other Bluetooth device...
Hi,
Lookin at this ticket https://devzone.nordicsemi.com/f/nordic-q-a/32090/qspi-pin-mux-on-nrf52840 for the nrf52840 it is said that it is ok to put QSPI on any pins (depending...
Hi,
I need to use cJson library to parse some json data. I have seen that the library is located at "nrf\ext\cjson" path. I have also seen how to add that library to a...
The documentation is VERY difficult to search. A search only goes over the chapter. I get different results depending upon which one I am in .... aarrg! And there are SOOO...
Hi,
I am not sure about the functionality of notify_cccd_handle.I am sending data from central to peripheral so the central should receive a notification from peripheral...
Very similar to this post , my use case involves cycling the modem between online and offline ("AT+CFUN=1" and "AT+CFUN=4"), for enabling GPS and also for reducing power consumption...
