Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi all ,
I have SHT31 and I can read Temperature and Humidity value by NRF52 . But I want to create 1 service for display it on smart phone with the RH (name: Humidity,...
Hello,
I would like to measure the voltage of circuit GND by using the embeded SAADC of nRF52832.
But unfortunately I have no vacancy of GPIO to connect GND.
Could you...
I have set up a nrf52840 kit to upload data to nrf cloud via bluetooth but the data on the cloud is displayed as a hexadecimal number(1,2,3,4,5,6,7,8,9,A,B......) I want to...
I am not seeing a transition to BLE_ADV_EVT_SLOW. The transition I see goes from FAST to idle, without a transition to slow, from the configuration I don't expect to be in...
I am trying to implement a timer using nrf_drv_timer.h and nrf_timer.h, however, the handler never gets called.
I first create a timer, then define a timer handler and finally...
Hello everyone! I am trying to program a nrf52832 sparkfun board through a nRF52DK. I have already gone through the pin connection guide succesfully and I can flash succesfully...
Hi there,
I could program the HEX file to nRF51DK via nRFgo studio successfully and the board seems to work fine as well. And then, I try to read back the HEX file from...
I am just wondering if it is possible to use the 52840's USB interface to create an R/NDIS type interface . The intention is to maybe create a WIFI/Cellular based Network...
Hi,
I am testing ble_app_att_mtu_throughput in SDK 14.2.0 between two nrf52832 DK board. One is act as a central and other one peripheral. I am placing these two boards...
Not a question, just to tell you that in ble_gatts_attr_t Struct Reference, documentation of « uint8_t* ble_gatts_attr_t::p_value », a « @ref » Doxygen markup has been produced
I have one pca10040 board, I want to realize the data transfer between the nrf52832 and the PC by BlueTooth, I use python3.5+PyBluez. When the nrf52832 is running the "ble_app_blinky...
The following lines are copied from the SDK15.0 documentation:
<pre>
Supported boards:
- PCA10040
- PCA10040E (nRF52810 emulation on PCA10040)
- PCA10056
- PCA10059 (support...
Hi, we are using
'iOSDFULibrary' , '~> 3.0' for firmware updation process. we are getting "DFU not found" error when device is already in dfu mode at the time of update...
Hello,
I've got the light_switch example running. I would like to extend this example with the possibility to send a broadcast messages from every node, the light client...
