Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello, I have been trying to setup eclipse for the NRF52 off and on all week. I followed the guide on setting up eclipse for the NRF51 and adapted it for the NRF52.
I've...
We have a factory in Hong Kong building and programming nRF51822 modules for us. We may go to a fancier solution in the future, but right now we are using nRFgo Studio and...
If I want to connect the NRF51822 board to Keil using JLink via SWD, I found the SW's clock frequency must below 20kHz. If I choose the higher frequency, the Keil can not...
I know this should be simple, but the prescaler is confusing me...
If I initialize my timers with a prescaler of 0, APP_TIMER_INIT(0, ...)
Then the max timer I can have...
Sorry but I've been stuck on this for a few days now and I have to give up and ask for help.
I'm attempting to set LED0 when BUTTON_0 is pressed and LED1 when BUTTON_1...
Hello all,
I am working on a device (nrf51 and s110) which is going to communicate with multiple centrals (smart phones).
The device uses a whitelist to connect to only...
Hi,
I run a custom board with an nrf51822.
If I program the device in the IAR IDE everything works fine but I cannot program the generated hexfile with nRFgo Studio or...
Is it 'NRF_RADIO->TASKS_DISABLE' or 'NRF_RADIO->TASKS_DISABLE = 1'?
Restarting advertisements seems not to be affected and I guess 'cancels out' NRF_RADIO->TASKS_DISABLE...
Hi,
I'm trying to run the uart loopback example in the nrf52 0.9.1 SDK with DMA enabled but it is being caught in an error catch. It runs fine without DMA enabled though...
We have some NRF51-DK devices here.
Recently we upgraded our segger software to v5.00.
During programming using nrfjprog we got the question to upgrade the emulator firmware...
I am trying to write a simple advertisement application for my nRF51822 development board (for it to run on an S110), but the tutorial on the nordicsemi.com website, which...
we are making a pedometer. when you are connected, you get notification for every step you make (just an integer)
you just did 50 steps. you can see it in the app. now...
I'm trying to implement a wake-up button on central multilink example. I.e, i need to implement the app_button in order to wake up from sd_evt_wat() function. The problem...
