I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Just want to know how acknowledged message works.
ANT document says there is no retry logic for acknowledged message.
According to ANT protocol, acknowledged message should...
Hi all!
I've been trying to OTA firmware using iOS nRF Toolbox App. I'm able to read.hex files in the App, although, after trying to send the file to the device the format...
I have a "heartbeat" LED which flashes for 10mS every 2 seconds. I was doing this with one of the HW timers and a PPI channel, but I have discovered that just having the HW...
How would I go about changing the connection event packet length?
I have an 8 byte characteristic setup with notifications enabled, but it still looks like it is transmitting...
Hi,
I have the following code with SD110 7.1.0:
static void uart_init(void) // device inter-communication
{
// Configure RX and TX pins.
nrf_gpio_pin_set(0);
nrf_gpio_cfg_output...
Hello,
I am building a sample protocol using nRF51822 DK. I am using S130 soft device. I have a few BLE nodes communicating with each other. The nRF51 DK acts as these nodes...
Is the nRF51822 pin-for-pin compatible with nRF51422?
I can't find any distributor stock of nRF51822-QFAC.
I see the eval kit has nRF51422. I don't need ANT functionality;...
Hii, i use nordic PCA10028 dev kit, to test the bluetooth of kit i simply load the ble_app_hrs example which is given in SDK, because of i don't know how softdevice 110 is...
I'm currently designing a system that requires Nonvolatile memory. Whilst I can accept the 43uS delay to write a word to flash memory. My concern is that it is entirely possible...
Hello,
i plan implementing an block storage for nRF51. I want to integrate an checksum or error correction mechanism.
I have understood i can write an bit 20000 times...
i meet very strange problem! i using nRF51822 QFAC. it has 32K RAM. but when we using 32K RAM Linkscript file. the firmware did not run up. it seem dead in sd_ble_enable(...
Greetings,
S110 with SDK6.0 I try to build the executable for Nordic GitHub project Timeslot Oberver example. I get an error that the handler SD_EVT_IRQHandler is multiple...
Hi,
There is a following initialization in 51822:
static void controls_init(void){
uint32_t err_code;
// Configure pins.
uint32_t pins_transition_mask = (1 << SCKIN_PIN...
I'm working on a project using the nRF51822 beacon kit (PCA20006), and I've downloaded the firmware files installer from the website. After running the installer, I can see...
