This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I'm using nRF52840 - QIAAD0 (it's revision 2 I think) and nrfx_saadc API v2 (but I don't think it doesn't really matter here)
tl;dr As stated in SAADC peripheral documentation...
Hello, i did my own custom board with a nrf52805 and I'm trying to put a module with different frames and when I do that my app is disconnecting 5seconds after. I didn't have...
Hello all,
I`m trying to use k_poll, it`s working okay, I just have an hard fauld error that drives me crazy, I have in main an loop which listen to k_pool_signals, the...
Hi,
Why I use the function m_device_state_set(cons, PM_DEVICE_STATE_SUSPENDED); to close the serial port is still a large current:38.80uA?
The verification method is as...
Hi there
I wrote SDK 17.2 ble_app_hrs to the module.
When connecting to an Android device, Empty PDUs will no longer be sent. I checked the RTC COUNTER, but it is incremented...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hi,
We are in the process of adding FOTA to our custom project and...
We are using nRF52833 with DFU secure bootloader and implemented DFU master/host on ESP32 BLE. We observe that DFU bootloader get stuck in above locations in softdevice more...
Hi Nordic
I have been using your example on USB MST to embed it into my application
Everything works ok, but in the main loop im constantly polling for USB power event...
I'm looking at the nRF Connect SDK Matter documentation, and the intro page states :
"If you are new to Matter, check also the tutorials on DevZone ."
The link in...
I am using nRF5340DK and would like to send and receive data to computer via UART1 and pins "TX", "RX", "CTS" and "RTS" using USB TO RS232 SERIAL CONVERTER.
This way I...
Hello Nordic, I have a problem. I'm running the nRF9160DK with three sensors and an sd card reader. The three sensors and the sd-card reader are connected via SPI. Due to...
Hi,
I would like to generate interrupts triggered by an input clock pin at 2 MHz to sample an 8-bit digital signal. I am trying this with an nRF5340. Up to this point...
Hello,
I am working with a nRF52833 and I am no longer able to use my JLink Base to flash it. I was previously able to flash it and there was no hardware change at all and...
