But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I'm try to follow the instructions for multi image example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html#ug-nrf5340-ses-multi...
Hello
I have 2 custom boards both with nRF82532. One is central and the other a peripheral. I use LESC. When no bonding information is stored in either of the devices, pairing...
Hello,
I am using mfw1.3.0 and NCS 1.7.0 developing an application on a custom board implementing the NRF9160 and NRF52820 (The 52820 is put into very low power using nrf_pwr_mgmt_shutdown...
Dear Nordic,
we need to save few bites (product serial number, few settings). we use BLE with bonding on a FreeRTOS based FW. PM is already using FDS, at it is not clear...
Hi,
We made a custom board with nRF52 and it's BLE radio doesn't advertising, not visible on nRF connect APP. RTT viewer is not showing any thing.
We used WLCSP package...
We have developed a small PCB that connects with some other HW. The integrated nRF52840 runs in HighVoltage-Mode and its required to set VDD to 3.0V. The question - how to...
Hey when i try and run my code runnning which is running the SAADC and transmitting data when its connecting with BLE but i can only get around 10 reading before i get a connection...
NRF51422 Custom board
SD310 v3.0
Phone: LG K8 4G
Android 6.0
SDK 9.0.0 Boot-loader example
I am testing over the air DFU with our custom device.
a.) DFU...
Hi there,
@Simonr, I need further help on this case
https://devzone.nordicsemi.com/f/nordic-q-a/58464/filtering-based-on-128-bit-uuid
It is said that it is possible...
For power optimization I did to disable Mesh Using this piece of Code
and Re- Enable using this code
So the Real Question is that , After disabling Mesh for some time...
Hi
I need a suggestion. We are like to try a long-distance I2C communication between the sensor & Nrf5340 that is we need to connect 1.5 meters of cable between them. So...
The device advertises.
The phone scans.
The device use white listing and only allow one peer, the phone.
What's the difference between erasing bonds and disabling white...
Hi there,
I'm intending to use the nrfxlib modem library and its BSD socket implementation on the nRF9160. My goal is to use non-blocking APIs and use `nrf_poll` in response...
Hi,
I followed the DFU to SDK example post on https://www.u-blox.com/en/docs/UBX-19050198 to add Buttonless DFU to an application (I modified \ble_peripheral\ble_app_hrs...
