But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I recently purchased a Thingy91 and have been following the start up guide but have been running into an issue with the thingy91 being recognized over USB. I was able to connect...
Hi Nordic,
I am developing a distance measurement application between the nrf52840 and nrf52833 unit for the long distance mode.
for the nrf52840 as center which running...
HI
I'm using SPI connecting to mutiple max31856(two now) on nrf52DK and SDK15.3
so I control my ss pin to pull low by myself
chip select by changing spi_pin like some...
a data array, length is 2048,use function "sd_ble_gattc_write", a error occurred, length less than 240, no error.
do {。。 err_code = write_configure(m_center_handle,14...
Hi all,
I'm using NRF SDK v17.0.2 and IEEE 802.15.4 stack library. I want to implement sleeping device. I think I should use sys_sleep_request_ms function to make the device...
Hello, Is it possible to use the USB Pins for Uart? no USB Protrocoll Would be nice if i can use the USB socket for UART with my other projects so i dont have to create a...
Hi,
There are new softdevices (v7.0.1) out for the nrf52832 and nrf52840 but, I don't see any mention of them on Nordic's infocentre. Are they compatible with SDK 16.0...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I have been working on DFU ble update with nrf52840 DK.
Using the onboard buttons I'm able to go to DFU mode where as for our custom board there's no buttons and I...
I am developing a firmware for the nRF52805 SoC with a nRF52 DK. I want to implement the DFU support on the same. The secure bootloader example in examples\dfu\secure_bootloader...
Hi everybody,
I'm trying to update a device (a PineTime device with a nrf52832). The firmware is using legacy DFU. I already have a DFU package, so, I only need to perform...
Hi,
I running a code that written on C and compiled with IAR for few years on nRF52832. Now i have a task to implement a new algorithm on embbeded but it was written with...
Hello, I'm flash download nrf52840 use st-link.
my softdevice version is s140, nrf5 sdk version is 13.0.0.
I want to flash download project, But I have an error.
...
Hello all Thank you for the many helpful posts I have encountered on this forum while continuing to discover the nRF5 SDK.
I have been trying out different examples for...
