Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
I am running flash_fstorage_example on the nRF52840 DK with SDK 15.0.0
I am having some problems with the example, as below:
1. When I run the example and use the shell...
Hi, I am trying to do MQTT disconnect, but I am always getting an error. First I successfully connect to the MQTT server, then I send some data, and then I want to disconnect...
Hi, I've been trying to use the nRF52840 Dongle to act as Bluetooth 5.0 peripherals but I cant seem to configure them for Long Range (coded PHY) detection. I am currently...
I ran one of my 9160 DK boards for 10 days using the Asset Tracker demo. The Hologram SIM card site I used says data exceeded 1 MB, which I understand the limit. Although...
Hi,
I have been trying to print out the float values using the NRF_LOG_FLOAT_MARKER, and i am only able to print 2 values in a single NRF_LOG_INFO line. Is there a way to...
Hello! I'm following the nRF52 Dongle programming guide to adapt the USB examples from SDK 15.3.0 to the nRF52840 Dongle. USB CDC ACM works fine, and I managed to get half...
Hello everyone,
I tried reading around the devzone and the infocenter , but I still didn't manage to solve my question.
In my scenario I'm using:
an nRF52832 as a...
Hi,
Sorry to bother you in your holidays.I want to get an conversion every time by calling nrfx_saadc_sample( ) .So I had configure saadc like below.But I found the adc...
Trying to print floats with NRF_LOG functions always prints a value of 0.00000.
E.g.
float value = 123.456; NRF_LOG_ERROR( "Float %f\r\n", value );
prints:
ERROR...
when I try to run: pip3 install -r mcuboot\scripts\requirements.txt, it fails with the following;
Collecting cryptography (from -r mcuboot\scripts\requirements.txt (line...
I'm trying out DFU functionality using nRF52840-PreviewDK and UART transport
On this page there is a table listing all the different combinations that can be downloaded...
Hi everyone,
I am currently working on a project that requires ICM-20648 and nRF52832. Is there an I2C driver available for these devices? The end goal would be to display...
I am using Keil and nrf52 dev kit to write some UART over BLE code if I set a break-point in nus_data_handler() it cause a reset to run soon after stepping though some code...
Hi to all,
i am developing an product based on the nrf5240 soc and i want to implement an hid device. after receiving some commands from HID i need to gather user presence...
Hello Nordic Support,
I am using SAADC on nRF52840 with nRF5_SDK_15.3.0_59ac345 .
I use the following configurations:
The SAADC value, as I have been using is signed...
