I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hello,
I am wondering that when BLE5.1 SDK will be available ?
Is there any possible ways to test your BLE direction finding solution ?
As far as I know, development...
I want to set a keep alive value of MQTT while eDRX is enabled, but it doesn't work well. Any advice?
Environment - hardware: nRF9160 DK 0.8.2 - firmware: 0.7.0-29.alpha...
Hi,
I am using nRF52832 SOC along with SDK v15.2.0 with custom hardware, currently I have requirement to use DFU protocol in BLE application to get a FW of another sub system...
Hello, I hope your day is full of the scent of flowers.
I am in the process of the Ble_Cnetral and PrePhereal project.
I have added and built the Uart.
Why is...
Hi frnds,
I am using the ble_central and ble_peripheral code (nrf52840).
i am sending 400 bytes of data to central from peripheral continuously, sometimes the boards get...
3.19 [78] TIMER: High current consumption when using timer STOP task only
I'm using app_timer_stop. But I do not know how to cope with this errata. Does the timer stop that...
Hi
After upgrade modem to mfw_nrf9160_1.0.0.
Most of our SIM cards still working good on both AT and MQTT projects.
Two of our SIM cards can't connect to LTE when uses...
Hi,
I'm using nRF52840 where it's written 1.0.0 on the jlink ship and QIAAC0 on the nRF ship.
When reading the info.variant register I got 0x41414330 which is ..AAC0...
Hello everyone,
I am using a NRF52840 development kit to write a custom protocol, so for the moment I am not using the softdevice but I am rather using the Radio as a...
We have a board built with the NRF9160 and an ADE9153A. The ADE9153A only responds to messages with odd parity. How do we set the NRF9160 to odd parity?
Hi,
I want nRF52 Continuous Unmodulated TX carrier.
Is it possible by TASK_TXEN and TASK_START or radio_tx_carrier command of radio test example, after TX configuration...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi, team I am trying to build a system with one master and multiple slaves using the mesh SDK. ( This is similar to the light_switch example. ) At this, I want to give each...
After the update to nRF Connect v3.0.0 none of the Nordic devices is detected anymore by that tool.
I even un-installed and reinstalled nRF Connect v3.0.0 (as recommended...
