We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello,
NRF52840
SDK 15.3.0
SoftDevice: s140
OS: Ubuntu
IDE: SES
I am having difficulty getting consistency out of the RTT + NRF_LOG_INFO() print statement. It...
Hello,
I use the nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31 with nrf52840-DK.
I'm looking for a way to get the transmit state after I sent a udp packet. I would like...
Hi,
we've been trying to reduce power consumption do I able to connect unused pins to GND directly?
Trace 1,2,3,4 do I able to connect to the GND?
Thanks, in advance...
Hi,
I am the first time programming with nordic and Segger. As I received the Thingy91 I just the getting started assistent to set up the toolchain.
This worked fine so...
I have the following setup, master (Nrf24L01) and several clients (Nrf52840), the clients listen, the master sends a message to one client and switches to listen. When the...
While most of nRF5 DSK modules have conditional compiling, such as
#if NRF_MODULE_ENABLED(BLE_DIS) the components/ble/ble_services/ble_dfu/*.c lack these macros. In my project...
Hello,
I use nRF5_SDK_15.3.0_59ac345 and ble_app_multiperipheral_pca10040_s132 .c code
In that code I integrate the capsense code it's work but after some time it's...
I'm want setting Secure_Bootloader.(IAR compiler, SDK 15.3version)
I followed the following guide but got stuck in Step B.
https://devzone.nordicsemi.com/nordic/nordic...
Hi All,
Can somebody point me to a Buttonless Secure Serial DFU Example from SDK16 or SDK15.3.0 for nRF52840-DK
I would use it with only Rx/Tx that is No Hardware Flow...
I want to read all data from a cluster is there a way to pass a wild card to
ZB_ZCL_GENERAL_ADD_ID_READ_ATTR_REQ(p_cmd, attr_id);
Or is there a smarter way to get the...
My nRF9160 DK is not able to connect to nRFCloud.com. I did the certificate update just in case to no avail. I have made sure to update the modem firmware to 1.01 and I used...
Hello, and thank you for making the nRFX components open-source on GitHub!
Now I realize that it's only been up for a day :smile: but most of the changes are reasonably...
Hi,
I'm moving from the nRF52 DK to using the nRF52832
https://media.digikey.com/pdf/Data%20Sheets/Fanstel%20PDFs/BC832_V2.01_Dec-2017.pdf
It can be hand soldered...
