We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I am currently using bluetooth mesh v2.1 which has qdid code QDID: 111537 , now we are currently added the Nodic uart service code, do i also have to declare the QDID 138862...
Hi, I want to create a peripheral device with a nRF52810 module.
Before developing the corresponding mobile app, I would like to use this as a central device: A GUI, written...
I have been trying to get a arduino UNO and arduino Leonardo to communicate with the nRF9160DK but have not been able. That accounts for the SPI example aswell as the I2C...
Given that Zephyr RTOS is not certified for use on Medical Devices, is there any plan to support operating systems with FDA 510(k), IEC 62304, IEC 60601 certifications?
...
I'm looking at augmenting the GPS system of the nRF9160 (at the moment due to high current and long time to acquire, easily lost sats/location) with some geolocation. Specifically...
I met a question here. Hope anybody can help on it, thanks.
I'm evaluating whether it is feasible to run the FFT algorithm on zephyr LTS project, with the nRF52832 board...
I want to know the upgradation process of firmware (Zephyr OS) on nordic nrf52840_pca10056. I have flashed the Zephyr OS on chip once via Jlink/JTAG, and now I want to flash...
Hello,
We are developing a product which includes qr code reading as its feature.with reference to https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo
as...
Dear All,
I need to develop a low-power application that sends a UDP message, waits for a certain amount of time (5 seconds) for a response and if there is no response it...
Hi,
Scenario : Scanning non mesh BLE packet with different stacks.
H/W Device - nRF52DK
Observation :
Case 1. Non Mesh BLE Stack (Soft device):: Here able to receive...
I'm working nrf52 DK, SDK V15.3 , S132 . I have created custom Services and characteristics its working fine. I need to change gap parameter in some cases because i need to...
Dear,
THINGY:91 / nRF91 DK
Currently, Power Saving Mode (PSM) is a feature that is not always available with roaming cards, and we must use the local sim card to use GPS...
It used to be downloadable, but now it's like this
The chip has the old code, and the chip can run the code
Is the chip's sdwio and sdwscl pins broken Or...
Hi,
Now I installed SEGGER Embedded Studio. But I got a activation key from SEGGER. I put the activation key into the IDE. After the I checked in the path "tools->License...
