We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I am using nRF9160: LTE Sensor Gateway to connect wiht nRF52832. My problem is I cannot re establish connection between the nRF9160 and the nRF52832. I have tried to create...
I am using nrf connect app on ios , the device is getitng on device mode but it is not showing DFU button on it , but it is working when using android app of it
And...
I want to generate a custom delay of one microsecond without using any timers By simply Executing instructions I want to generate. is there any possibility please let me know...
I have a rather strange issue.
I developed an application on the nrf52832 which amongst other, communicates with an ST Micro accelerometer LIS2DE12. The application works...
Hello,
Library seems to have limitation to 1kB. I'am talking about deffered mode.
You can increase NRF_LOG_DEFERRED_BUFSIZE >1kB, but it will crash if you try to print...
Hello, I am new to developing with nrf and have been trying to follow tutorials on individually setting pins as output. I am working on just getting a specified pin to blink...
Hi everyone,
Recently, I downloaded the SEGGER Embedded Studio, release 4.18, and start the development of a Heart Rate Monitor using nRF51422 and SDK 10 (softdevice s310...
I am only able to successfully trigger the ACK payload interrupt on the nRF24L01+ if I mismatch the payload lengths on the two devices; 4 for the nRF24L01+ and 1 for the nRF52840...
Hi everybody,
Intro facts :
I'm migrating from SDK 13.2.0 through SDK 14.2 to SDK 15.3.0. My program build on SDK14.2 but my product didn't work as expected, then I...
I need the P9 connector pinout (or complete schematic of Thingy:52 ) for programming my Nordic Thingy:52 using SWD. I have found this topics:
https://devzone.nordicsemi...
Hello, according to your website, nRF24 Series family is not recommended for new designs... as substitution you recommend to use nRF52 Series family. Can I ask you for the...
Aim: interface nrf32852 with i.MX6UL based Linux board through UART and configure hci of bluez. Board: nrf52_pca10040 SOM : nRf32852 OS: Zephyr UART: we followed HCI_UART...
Dear Nordic Team,
We are developing a custom board with nRF9160 with application of tracting device.
I am new user to this module and designing our device with target...
Hello,
I'm searching every where but i can't find what i want. Actually, i'm using two device and i really need to synchronise the execution of a process on both of them...
Hi All,
I have a problem to enable notification on my Android phone, i followed the tutorial on android web page (section bluetooth low energy) but my app crash, i have...
