Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I see that there are some simple HTTP examples in the sdk (ncs v1.0.0) but they are not as fully featured as the MQTT/S lib, is there a plan to do develop a simular lib for...
Hi,
I accidentally clicked on verify answer, is there a way to undo this?
It would be very nice if someone could still have a look at my problem, thanks.
https://devzone...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the SEGGER...
Hi All
I am now working in Channel Selection Algorithm (CSA), Bluetooth Low Energy. Basically, I would like to test both CSA 1 & 2, and also I would like to modify the CSA...
Setup:
SEGGER Embedded Studio for ARM (nordic Edition V4.18 (64 bit)
GCC
Windows 7 Professional
SDK: nRF5_SDK_15.3.0_59ac345
Issue:
In order to use the GPIO...
Eagle pcb and schematic reference designs on github are incorrect.
Reference nRF52840 pcb schematics and layouts are exactly the same for examples 2-6. I believe each is...
Hello,
I am using a nRF52840-DK with an HX711 in SES. I have been utilizing the code provided by Vidar Berg that can be seen here .
I downloaded the zip file, unzipped...
I'm developing the PCB schematic for a system using a nRF52 module that I found that suits my needs SKB369
At the same time I'm implementing a JTAG connector to flash my...
I was wondering: if the last sample of a buffer in the SAADC (using easyDMA and scan mode) is outside the limits, which interrupt would come first, the END or the LIMIT interrupt...
Hi, I am getting a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event since I increased the size of MAX MTU to 203 from 23. At first, I received INVALID PARAM error and then found out...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the...
hi,
I have developed light lightness model with the help of generic on/off and generic level model from the mesh SDK. And I have used these models by making changes in the...
Good afternoon,
I am trying to run the example "direct_test_mode" on a custom board based on a nrf52832.
I have succesfully run the example in two development kits ...
Hi,
I´m using nrf52840 with softdevice S132 and I wonder whether the ble_gattc_conn_cfg_t::write_cmd_tx_queue_size is a queue common for all connections or if it a queue...
