I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Here is a thing that I want to develop.
As my understanding, if I want to connect with PC I must use the HID example to achieve the event.
However, is it possible that...
I programmed an nRF52 (PCA10040) with the ble_app_beacon sample app and can see it advertising. However the nRF Beacon Android app does not detect it. nRF Beacon seems designed...
Hi,
I have a nrf52840 DK (pca10056) and a nrf52840 Dongle (pca10059).
I am using the following SDK versions:
nRF5_SDK_15.2.0_9412b96
nRF5_SDK_for_Thread_and_Zigbee_2...
HW: nrf52840
SW: nRF5_SDK_15.2.0_9412b96
Hi,
I would like to learn how allocate Flash, RAM and SRAM setting and how do I find out the total RAM/ROM my application...
Hi,
HW:customized nRF52840 board
SW: nRF5_SDK_15.2.0_9412b96
Application: modified blinky_rtc_freertos example (PWM led + freeRTOS task)
Q1) How to verify my application...
Hi,
I am try to try an IMU sensor (mpu60x0) via GPIO but it's giving me 0.6 Volts at output. I have configured the GPIO for High Drive (GPIO_PIN_CNF_DRIVE_H0H1)
Also I...
I am using the latest SDK 15.2
I am trying to build a network of "nodes" these nodes both scan and advertise and will connect with each other.
i currently have 7 NRF dev...
I had some trouble using Visual GDB, it seems their board support packages for nordic are not well updated. I really wanted to use VS studio for this project so I can organize...
I find that nrf5SDKforMeshv300src does not contain some documents, such as how_to_build_cmake.md, how_to_build_cmake_generating.md, how_to_build_cmake_generating_customization...
I have a project that generally operates as a typical peripheral, but occassionally sends advertising packets of type BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello Nordic Experts,
I am developing the pairing in a central. I am working on nRF52840 DK with nRF5_SDK_15.2.0_9412b96 as the cnetral and I have an iOS app as the peripheral...
We are using the nRF52832 with S332 v2.0 of the stack. We have recently been testing concurrent operation of a BLE peripheral connection and an ANT bidirectional master. The...
Hi all,
I'm using nRF52840 Development Kit and Nordic SDK v15.2.0 with soft device v6.1.0
I'm using ECDSA Cryptographic libraries for a BLE related project. I want to...
Hello,
I am working on Low power and Ultra Low power.
I am using the nrf52832 chip as well as the breakout board. In SYSTEM-ON mode power consumption around 6 mA and in...
How do I calculate round trip delay (time taken for packet to travel from peripheral to central(PC) to peripheral again)? Is the existing time calculation in the example code...
