We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello Sir,
I am working on home automation device in which I am using nRF24L01P module. Product is already in production. I bought these modules from local market which...
nrfutil install fail.
I want to update with BLE secure OTA, so install the nrfutil tool. and run the command as following:
but report download pc-ble-driver-py 0...
Total noob here using SES on a Mac to build BLE peripheral (S110) firmware for an nRF51822-based device with SDK v15.
So far I've been able to get the generic portions of...
Hi,
I'm developing on nrf52810 using the SDK14.1.0 and I've take as starting point a template application that targets nRF52810 running on the nRF52 Development Kit. But...
Taking a look through the SDK, there are very few examples using the dongle. I've tried building some of the existing examples by changing the board definition in the preprocessor...
I have a porject working well with normal ble function such as ancs and other services（use sdk15.0） , when I add the mesh model light switch on_off (source code copy from...
Hi.
I applied https://github.com/crfosse/Thingy-52-to-nRF52xx project for get thingy motion data by nRF52840.
But It still found 6 Service for motion service,...
I have a use case where I need to send a sequence of 2 byte bursts as SPI master. The data is generated on the fly and the algorithm would be able to saturate the 8Mbit/s...
Hi,
I just installed nrf connect 1.1 on my Dev-PC (many versions of J-Link and nrfjprog) everything works fine. The visualization of Secure-DFU-Upload-Speed is really nice...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
PDK: PCA10040
I am trying to read the ADC pin value using the SAADC module, I...
Hi, I'm using external board with nRF52832. (SDK 15.0.0)
In my external board, there are no RTS,CTS pin. So I don't use hardware flow control (HWFC).
The problem is, I...
How do I add a 128-bit UUID?
I am using SDK 14 and see hardly any examples of how to put a 128-bit UUID in my advertisements.
The only relevant example I found is under...
I am trying to package a firmware update and flash it over BLE DFU and I keep getting the following error on the nRF Toolbox app:
"Upload Failed: Unknown Command"
I cannot...
