Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I'm using nRf52840 rev B and C chipset and not able to detect the NFC on the device (the rev A chipset is working). Following SW combination is used:
nRF5_SDK_15.0...
Hello,
I am working on Multi-link. I want to scan the advertising information and connect only the uuid I set up.
I want to process it on_adv_report (), but I do not know...
The output order of my scanning Saadc is not predictable.
I found two related questions, but they both are for SDK 11 and seem to have been resolved.
devzone.nordicsemi...
Hi,
Am I right that after provisioner done with network configuration all nodes save their info in persistant storage and continue work without a provisioner?
How provisioner...
HI
i'm trying to use TSL2561 sensor, but i can't geting to work. I found the code that works on the psoc that, I change it so it fits nrf52840 but it still does not work...
I want to be sure about erasing flash. Flash is divided into pages and each page has 8 blocks. The smallest amount of flash you can erase is a PAGE. Is this correct. In other...
hello,
I'm currently stuck with sd_app_evt_wait() function leaving for an unknown reason. This function is called in the main loop.
The only reasons that shall exit the...
BLUETOOTH SPECIFICATION Version 5.0 | Vol 3, Part H page 2321 Figure 2.4
According to the figure, if an eavesdrop device exists in the pairing process, it is easy to obtain...
Hi support team,
I am currently working with the nRF8001 that I wanted to integrated on a my PCB.I would like to know if you have an antenna to recommend to work with the...
Hi everyone!
I inherited an product already in production using the nRF51422 QFAA Ex0 chip with the S310 V3 stack. I checked the compatibility matrix and found out the Ex0...
Dear Sir/Madam,
I tried to use GPIOTE and nrf_dev_gpiote at same prject on a MDK 5 project which is based on nRF5 SDK 10 and SoftDevice S110, but got this error:
.\_build...
HI, I found that the maximum number of connections 52832 can only be 15 connections, like this
// <o> NRF_SDH_BLE_CENTRAL_LINK_COUNT - Maximum number of central links....
Hello, everyone~
I need to connect nRF51822 and another big MCU with SPI. The big MCU is connected to a LTE module. The new firmware of nRF51822 need to be downloaded...
Hi
We're migrating our code from SDK14.2.0 to SDK15.0.0 and we can no longer see EXTSUPPLY as part of NRF_UICR_Type. Is there anywhere we can read about this change and...
