But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi Team, I am trying to add the nRF7000 support, for WIFI location, to our nRF9160 custom board. This is the lines I add to our device tree: prj.conf I am using the Location...
Hi team,
I am using nrf SDK 17.1.0 and using visual studio code editor with GCC compiler as IDE. I want to use nrf connect extension and use the advanced debugger features...
Respected Sir / Ma'am
We are trying to out the Locator Tag application
Successfully built and programmed the code on the nRF52840.
I can see the pop-up on the Google...
I'm working on optimizing power consumption in my project (using nRF5340DK; as well as Power Profiler Kit 2 which is connected to DK's VDD measurement point as an ampere meter...
Good Day All,
I'm having troubles with my nRF52840. (Specifically the nRF52840 18010 Holyiot module [http://www.holyiot.com/tp/2019042516322180424.pdf]) I've designed a...
I am looking for the nRF9151 variant of this document nan041: nRF9160 production programming . I do not currently see anything available on the technical documentation section...
I am working on CAF example Module and it has 4 pwms in overlay file.
1. Is it possible to add another PWM?
2. Is there any limit to number of PWMs and number of channels...
We have an existing application, based on the nordic softdevice s140nrf52701 that uses the AES algorithm, specifically ECB, CTR and CBC mode. We need to migrate to AES GCM...
Hi.
I’m trying to install Nordic Semiconductor’s nRF Connect SDK (NCS) version 1.9.2 via the command line. The standard nrfutil tool only supports versions 2.0.0 and above...
Hi,
I referred to the zephyr/samples/drivers/soc_flash_nrf/ code, and when I added CONFIG_BOOTLOADER_MCUBOOT=y , the flash storage started from address 0xfc000 . Why did...
Hi,
For a new product we would like to use Midi over BlueTooth (probably BLE). Is there support for this using some Nordic SDK (like the nRF Connect SDK)?
I can find several...
Hello everyone,
I’m facing an issue with my Thingy:91 . It was working fine throughout the day, but after flashing a program onto the nRF9160 , my computer no longer detects...
Hello. I am using nRF52832, SDK ver 15.3 and running it as a peripheral device. I use an interval timer to send a UART to an external device and receive an ACK. After running...
